All

Spartan Armor Systems Spartan AR550 Body Armor And Tactical Response Kit When purchasing this package you will receive: (1) Tactical Response Laser Cut Plate Carrier (Black, Coyote Brown, OD Green). (2) 10x12 Spartan AR550 Body Armor Shooters Cut Chest/Back Plates. Plate Carrier Specs: 1000 Denier Materials Light weight and Duty 1000 Denier laser Cut Molle Zippered Admin Pouch Kangaroo pouch with removable triple M4 Pouches Padded Shoulder Pads Padded Front and rear with ventilation vents Low Profile Drag Handle Molle Velcro front and rear for Identifier Patches 2-inch replaceable quick release buckles Accepts 10" x 12" Body Armor Comes with a Storage Bag Fits S to XL Our AR550 body armor is NIJ level III rated but has undergone special threat testing to achieve a level III+ rating. NIJ Certification applies to AR550 Shooters and Swimmers Cut Single Curve Full Coat armor plates.   Why Are Your AR550 Single Curve Full Coat Plates Labeled as Level III?  Spartan AR550 Single Curve, Full Coat body armor plates are labeled as level III on the back of the plate as the National Institute of Justice (NIJ) does not currently have a level III+ rating. Level III+ indicates special threat testing and was created by the body armor industry to fill the void between NIJ 0101.06 level III and NIJ level IV, specifically to account for high velocity penetrator rounds such as M855 (aka green tips). While Spartan AR550 single curve full coat plates are certified as NIJ level III, rest assured they are made from AR550 ballistic steel and have been special threat tested to level III+. Quite simply, the NIJ requires that we label AR550 single curve full coat plates as level III even though they are capable of higher ballistic protection.    Buy Body Armor - Level III+ Spartan AR550 Armor We’ve taken our Level III Body Armor to a NEW level! Spartan Armor Systems™ is pleased to introduce our AR550 Body Armor!  With a 10% increase in ballistic core hardness, our level III+ AR550 armor defeats higher velocity threats such as XM193, M855, and M80! We’re special rifle threat validated! Our AR550 armor hits the “sweet spot” in the Brinnell Hardness (BHN) range. With a core hardness of approximately 545-560 BHN, we have found our  ballistically rated variant of AR550 that we use is perfect for defeating higher velocity threats, while not exposing the armor plate to extreme stress due to forming. Our AR550 Level III+ armor has our GEN2 lower cut radius. With a 10% increase in core hardness, this ballistic grade steel is much harder than AR500, but not too hard to cause severe stress while forming. Advanced Triple Curve (ATC) AR550 Spartan Body Armor. An industry FIRST! Spartan Armor Systems™ is proud to be the FIRST in the industry to commercially offer triple-curved AR550 body armor. With higher velocity rifle threats commonly present throughout the United States, we’ve developed this AR550 armor to specifically defeat some common threats such as 5.56 x 45 XM193, 5.56 x 45 M855 /SS109 and 7.62 x 51 (.308 Winchester) at a rated velocity of 3,100 fps or less. Additionally, we’ve successfully defeated these threat profiles from Close Quarters Battle (CQB) distances…repeatedly! Level III+ Side Plates:   Choose from either 6″ x 6″ (small) or 6″ x 8″ (large) Chest Plate Weight (per plate):   10x12 AR550 Shooters Cut: Base Coat 8lbs 1oz. Full Coat 8lbs 10oz. Side Plate Weight (per plate):    6×6 approximately 2lbs 9oz (base coat), 2lbs 11oz (full coat), 6×8 approximately 3lbs 6oz (base coat), 3lbs 12oz (full coat). Thickness:   .25″ AR550 plus approximately .25″ coating (full coat) makes this slim profile plate overall .5-.6″ in total thickness As with all of our Armor products, we only use the highest grade of AR550 to manufacture our armor! Remember, not all body armor is created equal! Read our “FAQ” to find out more about the AR550 Armor we use to construct our body armor! Export Administration Regulations (EAR) and International Traffic in Arms Regulations (ITAR) - US Export Regulations: Level III and IV rifle rated body armor (Rifle Plates) fall under jurisdiction of the Export Administration Regulations (EAR) and International Traffic in Arms Regulations (ITAR), and are subject to the export control laws of the US Government. Export or re-transfer of Rifle Plates by any means to any foreign end user or for any other end use, whether in the US or abroad without written approval of the US Department of Commerce or Department of State is prohibited. The sale, transfer, transportation, or shipment outside of the US of any product prohibited or restricted for export without complying with US export control laws and regulations, including proper export licensing, documentation or authorization, is strictly prohibited and may result in civil penalties and/or constitute a federal crime. Spartan Armor Systems, TK Armor Systems, LLC will not engage in any transaction that requires the illegal export of any products and will not assist directly or indirectly with the illegal export or re-export of any products.

SPARTAN™ OMEGA™ AR500 BODY ARMOR SINGLE PLATE With Full Coat Frag Mitigation Coating Product Overview Armor befitting of a modern-day Spartan… The Spartan™ Omega™ AR500 Body Armor is sold as a pair of plates, and is constructed from ¼” thick lab certified AR500 Omega™ Armor ballistic-grade steel. The Spartan Omega AR500 plates are available in three sizes (8”x10”, 10”x12” and 11”x14”) and provide the operator with Level III protection in accordance with NIJ0101.06 standards. As with all other body armor sold by Spartan Armor Systems®, our Spartan™ Omega™ AR500 body armor has been independently tested and verified by an independent NIJ credentialed laboratory.   Spartan™ Omega™ AR500 Body Armor - True High-Quality Ballistic Threat Protection Not all steel core body armor is created equal! At Spartan Armor Systems® we are honored to provide our customers with the highest quality armor on the market because we understand intimately what is at stake. All Spartan™ Omega™ AR500 Body Armor products use only ballistic LAB CERTIFIED AR500 steel. All purchases of our Spartan Armor products have current lab certificates available on request, ensuring you have peace of mind when it comes to receiving the highest quality and integrity with your Spartan Armor Systems® body armor. For added peace of mind, every plate of armor sold by Spartan Armor Systems® is serialized allowing it to be easily tracked back to the original plate of steel it was cut from should there be any question as to its ballistic properties. Don’t settle for sub-standard, ineffective, low-quality steel armor - your life may depend on it. Read our "FAQ" to learn more about the extensive testing and quality assurance all Spartan™ Omega™ AR500 Body Armor is subjected to and to learn about the quality of steel we use to construct our body armor! Laser Cut to Protect Ballistic Integrity All steel core body armor is cut and shaped after the ballistic properties have been formulated within the steel. While other steel body armor manufacturers commonly use plasma torch cutting that applies excessive heat (25,000 ˚C / 45,000 ˚F) to a wide portion of the steel plate, Spartan Armor Systems® only utilizes laser cutting to protect the ballistic integrity throughout the entirety of each steel core body armor plate we manufacture. Plasma cutting also requires grinding to clean up the edges after the fact, resulting in increased heat and possible fatigue. At Spartan Armor Systems®, we maintain the highest production integrity and quality standards every step of the way for our customers because we know what is at stake.  Additional Protection: Full Coat or Base Coat Options We strongly recommend choosing our full coat option when you buy steel core body armor. Our proprietary plate coating, Encapsaloc™, is a potentially life-saving feature that captures spalling as a result of ballistic impacts on the strike face of the steel core armor plate. Do not settle for steel armor that is merely coated with generic truck bed liner spray coatings that have not been tested for ballistic efficacy. The strike face of our Spartan Armor Systems® Spartan™ Omega™ AR500 Body Armor plates proudly bears the mark of our Spartan logo.   IMPORTANT NOTE: The base coat option only provides protection against corrosion and offers little to no fragmentation/spall mitigation. Should you choose to select base coat plates, please consider adding our Spall Containment Sleeve (sold separately) as a means of fragmentation mitigation.   Exceptional Comfort & Engineering You have the choice of getting our Spartan™ Omega™ AR500 Body Armor formed on a continual radius die (single curve) or with our proprietary and patented Advanced Triple Curve™ (ATC) formation. It is important to note that our single curve plate is the equivalent of what our competitors deem “multi-curve” and our ATC design is a true multi-curve plate with unique curvature at the top, bottom, and sides of the plate. At Spartan Armor Systems® we have machined custom tooling to craft our plates with a sleek curvature that conforms and wraps to your torso for enhanced ergonomics. Spartan Armor Systems®™ is proud to be the FIRST in the industry to commercially offer the triple-curved Spartan™ Omega™ AR500 Body Armor. Spartan Armor Systems®’ ATC body armor allows the operator to shoulder their weapon with the most freedom and limited discomfort. The ATC design provides a snug, comfortable fit and “hugs” the operator’s body, resulting in a significant increase in comfort and operational maneuverability. Our custom-configured CNC equipment and advanced understanding of what makes Steel Core Armor most effective has allowed us to create dies that form our body armor without any “crease” bends. Crease-bends, “work hardens” the plate, which causes a significant amount of stress to the portion of the plate being placed under load during the manufacturing process. We HIGHLY suggest when doing your research, that you ask any manufacturer under consideration if they crease bend their body armor. This process results in increased potential for plate fatigue and failure, which is why Spartan Armor Systems®™ has gone the extra mile to create this unique die process.   Chest Plate Weight (per plate):  8”x10” Plate: Base Coat 5lbs 13oz. Full Coat 6lbs 7oz 10"x12" Plate: Base Coat 8lbs 10oz. Full Coat 9lbs 11oz. 11"x14" Plate: Base Coat 10lbs 1oz. Full Coat 11lbs 6oz. Additional Spartan™ Omega™ AR500 Body Armor - Specs:  Made in U.S.A. Meets NIJ 0101.06 Level III Specifications Available in Single Curve (commonly Called "MultiCurve" by other manufacturers) or Advanced Triple Curve™  Full Coat Option Provides Fragmentation/Spall Mitigation, Base Coat Provides Corrosion Protection Only Includes 1 Armor Plate Per Order Available in Shooters Cut or Swimmers Cut   See A Comparison of Our Full Line of Body Armor:   Export Administration Regulations (EAR) and International Traffic in Arms Regulations (ITAR) - US Export Regulations:   Level III and IV rifle rated body armor (Rifle Plates) fall under jurisdiction of the Export Administration Regulations (EAR) and International Traffic in Arms Regulations (ITAR), and are subject to the export control laws of the US Government. Export or re-transfer of Rifle Plates by any means to any foreign end user or for any other end use, whether in the US or abroad without written approval of the US Department of Commerce or Department of State is prohibited.   The sale, transfer, transportation, or shipment outside of the US of any product prohibited or restricted for export without complying with US export control laws and regulations, including proper export licensing, documentation or authorization, is strictly prohibited and may result in civil penalties and/or constitute a federal crime. Spartan Armor Systems, TK Armor Systems, LLC will not engage in any transaction that requires the illegal export of any products and will not assist directly or indirectly with the illegal export or re-export of any products.       *******All products available on this category are sold under and branded under Spartan Armor Systems ™ The Target Man’s /Spartan Armor Systems Spartan™ Omega™ AR500 Body Armor Armor products are manufactured from genuine, lab-certified AR500 ballistic grade steel. None of the products available on this website are sourced from, sponsored or approved by, affiliated with or in any way connected with Armored Republic, LLC.

When purchasing this package you will receive: (1) Achilles Plate Carrier (Black, Coyote Brown, OD Green) (2) 10x12 Spartan™ Omega™ AR500 Body Armor Shooters Cut Chest/Back Plates, Single Curve, Base Coat (2) 6x6 Spartan™ Omega™ AR500 Body Armor Side Plates, Curved, Base Coat You have the choice of 6x8 side plates, upgrade to Advanced Triple Curved™ ATC™, and upgrade to full coat for fragmentation mitigation on the package.  SPARTAN ARMOR SYSTEMS® ACHILLES LASER CUT PLATE CARRIER   Product Overview The Achilles Laser Cut Plate Carrier pays homage to the legendary Greek warrior, Achilles, a great hero of the Trojan War. Lightweight, durable, and highly adaptable the Achilles carrier is designed for the modern-day multi-role warrior. Comprised of lightweight 1000 Denier laser-cut Molle and featuring comfortable padded shoulder straps and padded front and rear sections with ventilation vents, Spartan Armor Systems® has also enhanced the capability of the Achilles Laser Cut Plate Carrier by adding our top-zippered admin pouch above a convenient kangaroo pouch that comes with removable triple M4 mag pouches.   Added Comfort And Capability Capability and comfort keep you in the fight longer. The Achilles Laser Cut Plate Carrier will accept both 10"x12" and 11"x14" body armor. For example, to increase comfort and protection it is possible to run our Flex Fused Core IIIA soft armor behind steel core plates such as our III+ AR550 10"x12" body armor utilizing the dual-chamber system! The cummerbund accepts side plates (6”x6” or 6"x8") and is modular/removable, with the inclusion of the built-in 2-inch quick-release straps. The configuration and customization options with the Achilles Laser Cut Plate Carrier are endless. Achilles Laser Cut Plate Carrier Specs:  1000 Denier Materials Lightweight And Duty 1000 Denier Laser Cut Molle Zippered Admin Pouch Kangaroo Pouch With Removable Triple M4 Pouches Padded Shoulder Pads Padded Front And Rear With Ventilation Vents Low Profile Drag Handle Molle Velcro Front And Rear For Identifier Patches 2-inch Replaceable Quick-release Buckles Accepts 10"X12" And 11"X14" Body Armor 6"X6" And 6"X8" Side Plates Fits S To XL SPARTAN™ OMEGA™ AR500 BODY ARMOR SHOOTERS CUT SET OF TWO   Product Overview Armor befitting of a modern-day Spartan… The Spartan™ Omega™ AR500 Body Armor is sold as a pair of plates, and is constructed from ¼” thick lab certified AR500 Omega™ Armor ballistic-grade steel. Spartan™ Omega™ AR500 plates provide the operator with Level III protection in accordance with NIJ0101.06 standards. As with all other body armor sold by Spartan Armor Systems®, our Spartan™ Omega™ AR500 body armor has been independently tested and verified by an independent NIJ credentialed laboratory.    Spartan™ Omega™ AR500 Body Armor - True High-Quality Ballistic Threat Protection Not all steel core body armor is created equal! At Spartan Armor Systems® we are honored to provide our customers with the highest quality armor on the market because we understand intimately what is at stake. All Spartan™ Omega™ AR500 Body Armor products use only ballistic LAB CERTIFIED AR500 steel. All purchases of our Spartan Armor products have current lab certificates available on request, ensuring you have peace of mind when it comes to receiving the highest quality and integrity with your Spartan Armor Systems® body armor. For added peace of mind, every plate of armor sold by Spartan Armor Systems® is serialized allowing it to be easily tracked back to the original plate of steel it was cut from should there be any question as to its ballistic properties. Don’t settle for sub-standard, ineffective, low-quality steel armor - your life may depend on it. Read our "FAQ" to learn more about the extensive testing and quality assurance all Spartan™ Omega™ AR500 Body Armor is subjected to and to learn about the quality of steel we use to construct our body armor!   Laser Cut to Protect Ballistic Integrity All steel core body armor is cut and shaped after the ballistic properties have been formulated within the steel. While other steel body armor manufacturers commonly use plasma torch cutting that applies excessive heat (25,000 ˚C / 45,000 ˚F) to a wide portion of the steel plate, Spartan Armor Systems® only utilizes laser cutting to protect the ballistic integrity throughout the entirety of each steel core body armor plate we manufacture. Plasma cutting also requires grinding to clean up the edges after the fact, resulting in increased heat and possible fatigue. At Spartan Armor Systems®, we maintain the highest production integrity and quality standards every step of the way for our customers because we know what is at stake.  Additional Protection: Full Coat or Base Coat Options We strongly recommend choosing our full coat option when you buy steel core body armor. Our proprietary plate coating, Encapsaloc™, is a potentially life-saving feature that captures spalling as a result of ballistic impacts on the strike face of the steel core armor plate. Do not settle for steel armor that is merely coated with generic truck bed liner spray coatings that have not been tested for ballistic efficacy. The strike face of our Spartan Armor Systems® Spartan™ Omega™ AR500 Body Armor plates proudly bears the mark of our Spartan logo.    IMPORTANT NOTE: The base coat option only provides protection against corrosion and offers little to no fragmentation/spall mitigation. Should you choose to select base coat plates, please consider adding our Spall Containment Sleeve (sold separately) as a means of fragmentation mitigation.    Exceptional Comfort & Engineering You have the choice of getting our Spartan™ Omega™ AR500 Body Armor formed on a continual radius die (single curve) or with our proprietary and patented Advanced Triple Curve™ (ATC) formation. It is important to note that our single curve plate is the equivalent of what our competitors deem “multi-curve” and our ATC design is a true multi-curve plate with unique curvature at the top, bottom, and sides of the plate. At Spartan Armor Systems® we have machined custom tooling to craft our plates with a sleek curvature that conforms and wraps to your torso for enhanced ergonomics. Spartan Armor Systems®™ is proud to be the FIRST in the industry to commercially offer the triple-curved Spartan™ Omega™ AR500 Body Armor. Spartan Armor Systems®’ ATC body armor allows the operator to shoulder their weapon with the most freedom and limited discomfort. The ATC design provides a snug, comfortable fit and “hugs” the operator’s body, resulting in a significant increase in comfort and operational maneuverability. Our custom-configured CNC equipment and advanced understanding of what makes Steel Core Armor most effective has allowed us to create dies that form our body armor without any “crease” bends. Crease-bends, “work hardens” the plate, which causes a significant amount of stress to the portion of the plate being placed under load during the manufacturing process. We HIGHLY suggest when doing your research, that you ask any manufacturer under consideration if they crease bend their body armor. This process results in increased potential for plate fatigue and failure, which is why Spartan Armor Systems®™ has gone the extra mile to create this unique die process.    Chest Plate Weight (per plate):  10"x12" Plate: Base Coat 8lbs 10oz. Full Coat 9lbs 11oz. Side Plate Weight (per plate): 6×6 approximately 2lbs 1oz (base coat) or 2lbs 15oz (full coat) 6×8 approximately 3lbs 10oz (base coat) or 3lbs 14oz (full coat) Additional Spartan™ Omega™ AR500 Body Armor - Specs:  Made in U.S.A. Meets NIJ 0101.06 Level III Specifications Available in Single Curve (commonly Called "MultiCurve" by other manufacturers) or Advanced Triple Curve™  Full Coat Option Provides Fragmentation/Spall Mitigation, Base Coat Provides Corrosion Protection Only   See A Comparison of Our Full Line of Body Armor:   Export Administration Regulations (EAR) and International Traffic in Arms Regulations (ITAR) - US Export Regulations:   Level III and IV rifle rated body armor (Rifle Plates) fall under jurisdiction of the Export Administration Regulations (EAR) and International Traffic in Arms Regulations (ITAR), and are subject to the export control laws of the US Government. Export or re-transfer of Rifle Plates by any means to any foreign end user or for any other end use, whether in the US or abroad without written approval of the US Department of Commerce or Department of State is prohibited.   The sale, transfer, transportation, or shipment outside of the US of any product prohibited or restricted for export without complying with US export control laws and regulations, including proper export licensing, documentation or authorization, is strictly prohibited and may result in civil penalties and/or constitute a federal crime. Spartan Armor Systems, TK Armor Systems, LLC will not engage in any transaction that requires the illegal export of any products and will not assist directly or indirectly with the illegal export or re-export of any products.       *******All products available on this category are sold under and branded under Spartan Armor Systems ™ The Target Man’s /Spartan Armor Systems Spartan™ Omega™ AR500 Body Armor Armor products are manufactured from genuine, lab-certified AR500 ballistic grade steel. None of the products available on this website are sourced from, sponsored or approved by, affiliated with or in any way connected with Armored Republic, LLC.     See A Comparison of Our Full Line of Body Armor:

When purchasing this package you will receive: (1) Tactical Response Laser Cut Plate Carrier (Black, Coyote Brown, OD Green). (2) 10x12 Spartan™ Omega™ AR500 Body Armor Shooters Cut Chest/Back Plates. Plate Carrier Specs: 1000 Denier Materials Light weight and Duty 1000 Denier laser Cut Molle Zippered Admin Pouch Kangaroo pouch with removable triple M4 Pouches Padded Shoulder Pads Padded Front and rear with ventilation vents Low Profile Drag Handle Molle Velcro front and rear for Identifier Patches 2-inch replaceable quick release buckles Accepts 10" x 12" Body Armor Comes with a Storage Bag Fits S to XL Constructed from lab certified Spartan™ Omega™ AR500 Body Armor, (1/4” thickness) these plates provide the operator with Level III protection IAW NIJ0101.06 standards. With all of our Spartan™ Omega™ AR500 Body Armor products, we only use ballistic LAB CERTIFIED AR500 steel! All purchases of our Spartan Armor products have current lab certificates available on request. Remember, not all body armor is created equal! Read our "FAQ" to find out more about the steel we use to construct out body armor! You have the choice of getting our Spartan™ Omega™ AR500 Body Armor formed on a continual radius die. Or with our Advanced Triple Curve ™.  Instead of bending our formed plates in 2 different locations as we used to, we have machined custom tooling to give these plates a nice curvature to best conform to the side of your torso. Spartan Armor Systems™ is proud to be the FIRST in the industry to commercially offer triple-curved Spartan™ Omega™ AR500 Body Armor. Spartan Armor Systems’ ATC™ body armor allows the operator to shoulder their weapon with the most freedom and limited discomfort. The ATC™ armor better “hugs” the operator’s body, resulting in a significant increase in comfort. Our CNC equipment capabilities have allowed us to create dies which form our body armor without any “crease” bends. Crease bends, “work hardens” the plate and causes a significant amount of stress to the portion of the plate under load. We HIGHLY suggest when doing research to ask if they crease bend their body armor. This process results in increased potential for plate fatigue and failure, which is why Spartan Armor Systems™ has gone the extra mile to create this die process.  Full Coat or Base Coat Options:  We are excited to announce our potentially “life saving” breakthrough!  The strike face for our plates is mark embedded with our Spartan logo! Both sides of these plates are coated, however, the back side only has a “courtesy coat” to protect against wear and rust. The front of the plate is lined with 1/4-3/8 of our proprietary coating, Encapsaloc ™.  The result is a plate approximately 1/2-5/8” total thickness.  See our FAQ for more information about our Encapsaloc ™ process. Due to popular demand, we have added a “base coat” only option for our AR500 armor products. The base coat option has an extremely thin layer of our fragmentation mitigation coating to aesthetically enhance the plates, and to provide corrosion resistance. This coating has minimal, if any, fragmentation mitigation capabilities.   Chest Plate Weight (per plate): 10x12 Spartan™ Omega™ AR500 Body Armor Shooters Cut: Base Coat 8lbs 10oz. Full Coat 9lbs 11oz.   Side Plate Weight (per plate): 6×6 approximately 2lbs 1oz (base coat) 2lbs 15oz (full coat), 6×8 approximately 3lbs 10oz (base coat) 3lbs 14oz (full coat).   Advanced Triple Curve™ (ATC) Spartan™ Omega™ AR500 Body Armor | Spartan Armor Systems™ With our Spartan™ Omega™ AR500 Body Armor Advanced Triple Curve™ body armor, the operator now has increased comfort. The Spartan™ Omega™ AR500 Body Armor, cut from genuine lab-certified Omega Armor, offers advanced Level III protection. We’ve taken everything in to consideration, to include ergonomics, functionality, and price point.   Export Administration Regulations (EAR) and International Traffic in Arms Regulations (ITAR) - US Export Regulations: Level III and IV rifle rated body armor (Rifle Plates) fall under jurisdiction of the Export Administration Regulations (EAR) and International Traffic in Arms Regulations (ITAR), and are subject to the export control laws of the US Government. Export or re-transfer of Rifle Plates by any means to any foreign end user or for any other end use, whether in the US or abroad without written approval of the US Department of Commerce or Department of State is prohibited. The sale, transfer, transportation, or shipment outside of the US of any product prohibited or restricted for export without complying with US export control laws and regulations, including proper export licensing, documentation or authorization, is strictly prohibited and may result in civil penalties and/or constitute a federal crime. Spartan Armor Systems, TK Armor Systems, LLC will not engage in any transaction that requires the illegal export of any products and will not assist directly or indirectly with the illegal export or re-export of any products.   *******All products available on this category are sold under and branded under Spartan Armor Systems ™ The Target Man’s /Spartan Armor Systems Spartan™ Omega™ AR500 Body Armor products are manufactured from genuine, lab-certified AR500 ballistic grade steel. None of the products available on this website are sourced from, sponsored or approved by, affiliated with or in any way connected with Armored Republic, LLC. See A Comparison of Our Full Line of Body Armor:

SPARTAN ARMOR SYSTEMS® SENTINEL PLATE CARRIER   Product Overview The Spartan Armor Systems® Sentinel Plate Carrier is an extremely rugged, lightweight, feature-packed plate carrier that affords users a high degree of comfort and customization. Whether you are shopping for your first plate carrier or your next plate carrier, the Sentinel carrier platform allows the operator significant freedom to build and customize to fit their needs.  Ready For Anything Fitting 38” to 48” chest sizes, the Sentinel Plate Carrier is fabricated from 1000 denier fabric and fits 10"x12" shooters cut plates. Featuring anti-slip shoulder padding with velcro, side release buckles, and a highly breathable padded mesh throughout the interior for comfort the Sentinel Plate Carrier affords all-day comfort and wearability. The removable cummerbund features removable side plate pockets for both 6"x6" and 6"x8" plate armor inserts for added protection. The Spartan Armor Systems Sentinel Plate Carrier has been one of our most popular carriers with thousands having been sold to Law Enforcement Officers and Civilians alike. Spartan Armor Systems® Sentinel Plate Carrier Specs: Adjustable from 38" To 48" Chest Size Durable Emergency Drag Handle Anti-slip Shoulder Padding With Velcro Side Release Buckles On The Internal Waist Strap Padded Mesh Separators For The Interior Of The Carrier For Breathability Fits 10" X 12" Shooters Cut Plates Removable Cummerbund With Side Plate Pockets For 6" X 6" And 6" X 8" Side Plate Armor Velcro In Front Of The Carrier Is 8” X 4” With A Velcro Loop On Each Side Velcro On The Back Of The Carrier Measures 9” X 3” Stronger Carrier Material That Can Withstand Extensive Wear And Tear Over A Long Period Of Time 1000 Denier Bottom Loading Weighs Approximately 2lbs. 9oz. NOTE: This plate carrier CAN accept 6"x8" side plates. There is a flap of Velcro inside each side plate pocket that must be flipped vertically to allow for 6"x8" side plates. SPARTAN™ OMEGA™ AR500 BODY ARMOR SHOOTERS CUT SET OF TWO   Product Overview Armor befitting of a modern-day Spartan… The Spartan™ Omega™ AR500 Body Armor is sold as a pair of plates, and is constructed from ¼” thick lab certified AR500 Omega™ Armor ballistic-grade steel. Spartan Omega AR500 plates provide the operator with Level III protection in accordance with NIJ0101.06 standards. As with all other body armor sold by Spartan Armor Systems®, our Spartan™ Omega™ AR500 body armor has been independently tested and verified by an independent NIJ credentialed laboratory.    Spartan™ Omega™ AR500 Body Armor - True High-Quality Ballistic Threat Protection Not all steel core body armor is created equal! At Spartan Armor Systems® we are honored to provide our customers with the highest quality armor on the market because we understand intimately what is at stake. All Spartan™ Omega™ AR500 Body Armor products use only ballistic LAB CERTIFIED AR500 steel. All purchases of our Spartan Armor products have current lab certificates available on request, ensuring you have peace of mind when it comes to receiving the highest quality and integrity with your Spartan Armor Systems® body armor. For added peace of mind, every plate of armor sold by Spartan Armor Systems® is serialized allowing it to be easily tracked back to the original plate of steel it was cut from should there be any question as to its ballistic properties. Don’t settle for sub-standard, ineffective, low-quality steel armor - your life may depend on it. Read our "FAQ" to learn more about the extensive testing and quality assurance all Spartan™ Omega™ AR500 Body Armor is subjected to and to learn about the quality of steel we use to construct our body armor!   Laser Cut to Protect Ballistic Integrity All steel core body armor is cut and shaped after the ballistic properties have been formulated within the steel. While other steel body armor manufacturers commonly use plasma torch cutting that applies excessive heat (25,000 ˚C / 45,000 ˚F) to a wide portion of the steel plate, Spartan Armor Systems® only utilizes laser cutting to protect the ballistic integrity throughout the entirety of each steel core body armor plate we manufacture. Plasma cutting also requires grinding to clean up the edges after the fact, resulting in increased heat and possible fatigue. At Spartan Armor Systems®, we maintain the highest production integrity and quality standards every step of the way for our customers because we know what is at stake.    IMPORTANT NOTE: The base coat option only provides protection against corrosion and offers little to no fragmentation/spall mitigation. Should you choose to select base coat plates, please consider adding our Spall Containment Sleeve (sold separately) as a means of fragmentation mitigation.    Exceptional Comfort & Engineering You have the choice of getting our Spartan™ Omega™ AR500 Body Armor formed on a continual radius die (single curve) or with our proprietary and patented Advanced Triple Curve™ (ATC) formation. It is important to note that our single curve plate is the equivalent of what our competitors deem “multi-curve” and our ATC design is a true multi-curve plate with unique curvature at the top, bottom, and sides of the plate. At Spartan Armor Systems® we have machined custom tooling to craft our plates with a sleek curvature that conforms and wraps to your torso for enhanced ergonomics. Spartan Armor Systems®™ is proud to be the FIRST in the industry to commercially offer the triple-curved Spartan™ Omega™ AR500 Body Armor. Spartan Armor Systems®’ ATC body armor allows the operator to shoulder their weapon with the most freedom and limited discomfort. The ATC design provides a snug, comfortable fit and “hugs” the operator’s body, resulting in a significant increase in comfort and operational maneuverability. Our custom-configured CNC equipment and advanced understanding of what makes Steel Core Armor most effective has allowed us to create dies that form our body armor without any “crease” bends. Crease-bends, “work hardens” the plate, which causes a significant amount of stress to the portion of the plate being placed under load during the manufacturing process. We HIGHLY suggest when doing your research, that you ask any manufacturer under consideration if they crease bend their body armor. This process results in increased potential for plate fatigue and failure, which is why Spartan Armor Systems®™ has gone the extra mile to create this unique die process.    Chest Plate Weight (per plate):  10"x12" Plate: Base Coat 8lbs 10oz. Side Plate Weight (per plate):  6×6 approximately 2lbs 1oz (base coat)   Additional Spartan™ Omega™ AR500 Body Armor - Specs:  Made in U.S.A. Meets NIJ 0101.06 Level III Specifications Available in Single Curve (commonly Called "MultiCurve" by other manufacturers) or Advanced Triple Curve™  Full Coat Option Provides Fragmentation/Spall Mitigation, Base Coat Provides Corrosion Protection Only   See A Comparison of Our Full Line of Body Armor:   Export Administration Regulations (EAR) and International Traffic in Arms Regulations (ITAR) - US Export Regulations:   Level III and IV rifle rated body armor (Rifle Plates) fall under jurisdiction of the Export Administration Regulations (EAR) and International Traffic in Arms Regulations (ITAR), and are subject to the export control laws of the US Government. Export or re-transfer of Rifle Plates by any means to any foreign end user or for any other end use, whether in the US or abroad without written approval of the US Department of Commerce or Department of State is prohibited.   The sale, transfer, transportation, or shipment outside of the US of any product prohibited or restricted for export without complying with US export control laws and regulations, including proper export licensing, documentation or authorization, is strictly prohibited and may result in civil penalties and/or constitute a federal crime. Spartan Armor Systems, TK Armor Systems, LLC will not engage in any transaction that requires the illegal export of any products and will not assist directly or indirectly with the illegal export or re-export of any products.       *******All products available on this category are sold under and branded under Spartan Armor Systems ™ The Target Man’s /Spartan Armor Systems Spartan™ Omega™ AR500 Body Armor Armor products are manufactured from genuine, lab-certified AR500 ballistic grade steel. None of the products available on this website are sourced from, sponsored or approved by, affiliated with or in any way connected with Armored Republic, LLC.

SHELLBACK TACTICAL 10 X 12 TRIPLE-CURVE SWIMMER CUT LEVEL IV HARD ARMOR PLATE MODEL 26605-2 Level IV Model 26605-2 Plate Features NIJ threat level IV standalone protection NIJ 0101.06 Certified - Listed on NIJ compliant armor list  Manufactured from high-density alumina ceramic core (AI203) backed with layered woven aramid fiber Wrapped with black Cordura nylon covering  Swimmer cut   Triple curve 10" W x 12"L x 1"D Weight 6.9LBS  5 year ballistic warranty  Made in the USA by LTC - Leading Technology Composites Rounds Defeated .357 SIG FMJ  9MM .38 .40 S&W .44 .45 5.56 x 45mm - M193/M855/SS109 7.62 x 54R - LPS  7.62 x 54R - B-32 API 7.62 x 39mm - API 7.62 x 39mm - Ball 7.62 x 51mm - M80 Ball 7.62 x 36 M2AP

The ALL NEW MAXX-DRI VEST 3.0 has been completely re-designed to MAXXIMIZE body armor ventilation, airflow and improve weight-distribution of your ballistic vest, making it feel lighter and more comfortable on your body!! The MAXX-DRI Vest allows exceptional ventilation and cooling making it perfect for extended duty use by Law Enforcement, Security Professionals and Civilians who train often. Wearing a plate carrier for a long period of time, or even just in a warm climate creates additional fatigue and dehydration for the operator. We highly recommend the MAXX-DRI Vest to increase the comfort of your plate carrier and reduce fatigue. FEATURES Patented Full Maxx-Dri Construction (Maxximum body armor ventilation) NEW patented dual-chambered design for increased cooling/ventilation NEW Velcro Side Closures for easy donning and doffing NEW Stay-put Grip Technology prevents your Maxx-Dri vest from shifting Triple reinforced stitching for Maxximum strength and durability Lifetime Warranty against manufacturer defects (does not include wear) FULL 360 DEGREE COVERAGE everywhere your body armor rests Velcro shoulder straps allow you to keep it secured to your body armor Anti-microbial and Anti-Fungal Does not retain moisture Anti-Gravity effect helps reduce neck/back pain and fatigue A decrease in the likelihood of developing dangerous skin rashes and infections A less stinky under shirt and a less sweat-soaked body armor carrier to bring home to launder An overall feeling of comfort by having your ballistic vest feel lighter on your body N.T.O.A. Member Tested and Recommended   

PRODUCT SPECS Emergency drag handle Removable padded anti-slip shoulder pads with hook and loop guidelines Adjustable shoulder straps MOLLE webbing for modular attachments Hook and loop webbing Front map pocket with snap, hook and loop closure Back auxiliary pocket with hook and loop closure Adjustable cummerbund with built-in soft armor pockets Breathable 3D Mesh liner Ballistic plates/soft armor not included Easy access plate pockets Plate Capacity: Small/Medium: accepts Medium BALCS/SPEAR cut soft armor & plates up to 10” x 12.5” Large/X-Large: accepts Large BALCS/SPEAR cut soft armor & plates up to 11” x 14” (Plate thickness should be less than 1/2” to fit) Cummerbund Size: Small/Medium: adjustable from 34” - 42” Large/X-Large: adjustable from 43” - 50” Soft Armor cummerbund capacity: Small/Medium: accepts Medium 6” x 10” soft armor Large/X-Large: accepts Large 6” x 12” soft armor CONDOR EXO PLATE CARRIER GEN II Condor had maximum protection in mind when it came this plate carrier. The Condor EXO Gen II Plate Carrier is designed to hold soft armor and plates. The EXO Plate Carrier will not leave you unprotected when you need it most whether you are just being prepared or knowingly entering a dangerous environment. This carrier offers a padded interior and shoulders for the utmost comfort and articulation. You will never have to worry again about performance as the EXO Plate Carrier will keep you performing at the best of your ability so the team doesn’t have to use the emergency drag handle because you can hardly keep up. PRODUCT SPECS Emergency drag handle Removable padded anti-slip shoulder pads with hook and loop guidelines Adjustable shoulder straps MOLLE webbing for modular attachments Hook and loop webbing Front map pocket with snap, hook and loop closure Back auxiliary pocket with hook and loop closure Adjustable cummerbund with built-in soft armor pockets Breathable 3D Mesh liner Ballistic plates/soft armor not included Easy access plate pockets Plate Capacity: Small/Medium: accepts Medium BALCS/SPEAR cut soft armor & plates up to 10” x 12.5” Large/X-Large: accepts Large BALCS/SPEAR cut soft armor & plates up to 11” x 14” (Plate thickness should be less than 1/2” to fit) Cummerbund Size: Small/Medium: adjustable from 34” - 42” Large/X-Large: adjustable from 43” - 50” Soft Armor cummerbund capacity: Small/Medium: accepts Medium 6” x 10” soft armor Large/X-Large: accepts Large 6” x 12” soft armor

Features: Holds radio, with space for antenna, ear bud, and/or microphone Elastic band and hook and loop flap MOLLE compatible Overall dimensions: 8"H x 4.5"W x 2"D Available in: Olive Drab Black Navy Multicam Condor Radio Pouch Features: Holds radio, with space for antenna, ear bud, and/or microphone Elastic band and hook and loop flap MOLLE compatible Overall dimensions: 8"H x 4.5"W x 2"D Available in: Olive Drab Black Navy Multicam

Condor MOPC GEN2 Multicam The Condor Outdoor Modular Operator Plate Carrier is made up of quality nylon material and is designed for complete ballistic protection carrier (Ballistic plates/soft armor not included). MOLLE webbing surrounds the carrier to allow for modular attachments and personalization. The padded adjustable shoulder straps and cummerbund ensure a true fit. This unique cummerbund features integrated soft armor pockets and it’s compatible with our side plate. The interior is lined with 3D mesh to ensure ventilation and active comfort. The MOPC by Condor Outdoor is ready to take on any fight.   Specifications:  Cummerbund Size: Adjustable from 40" - 48" Plate capacity: Cummerbund accepts soft armor inserts up to 6" x 11" Accepts Medium or Large Swimmer/ESAPI plates up to 10.25" x 13.25 Removable low profile shoulder pads Adjustable shoulder straps Breathable 3D mesh liner Front map pocket with snap, hook and loop closure Adjustable cummerbund with built-in soft armor pockets MOLLE webbing for modular attachments Hook and loop webbing Easy access plate pockets Ballistic plates/soft armor not included Imported **Gen2 cummerbund will only accept soft armor.    

The Condor Defender Plate Carrier is designed to carry both soft armor and plate. It will accept Large or X-Large SPEAR/BALC cut soft armor, up to 10.25" x 13.25" front and back plates, and up to 6" x 8" side plates. The DFPC also features mesh padding for airflow and padded shoulders for added comfort. The Condor Defender Plate Carrier The Condor Defender Plate Carrier is designed to carry both soft armor and plate. It will accept Large or X-Large SPEAR/BALC cut soft armor, up to 10.25" x 13.25" front and back plates, and up to 6" x 8" side plates. The DFPC also features mesh padding for airflow and padded shoulders for added comfort. Available in genuine Crye-Precision™ MultiCam® Emergency drag handle. Removable padded shoulder pads, with hook and loop guides Adjustable shoulder straps Heavyweight webbing for modular attachments Padded mesh interior lining Adjustable cummerbund with soft armor pockets Accepts up to 6" x 8" side panel plates Internal sleeves for soft armor Easy access plate pockets Adjustable in girth and height Medium - XX-Large adjustable sizing Accepts Large or X-Large BALCS/SPEAR cut soft armor, and plates up to 10.25" x 13.25" Imported

SPARTAN ARMOR SYSTEMS® "SPARTAN" SHOOTERS CUT PLATE CARRIER   Product Overview The Spartan Armor Systems® "Spartan" Plate Carrier is true to its name: sleek, minimalist, and highly capable on the battlefield. Designed to be lightweight, agile, and to enable the wearer to rapidly engage, the Spartan Armor Systems® “Spartan” Shooters Cut Plate Carrier is designed for use with our shooters cut steel core armor: Spartan™ Omega™ AR500 and AR550. Adjustable from Medium to XL, this carrier fits 10”x12” shooters cut plates and will accommodate 6”x6” side plates in the cummerbund. The Spartan Shooters Cut Plate Carrier is built to last and gives you the key essential features you need without sacrificing quality. The Spartan Shooters Cut Carrier is a great entry-level carrier that offers a variety of features at an affordable price point. When the situation dictates less is more, this carrier delivers the goods where it counts.    Spartan Armor Systems® Spartan Shooters Cut Plate Carrier Specs: Lightweight Plate Carrier That Accepts Side Plates Designed For Spartan Armor Systems® 10” X 12” Shooters Cut Steel Core Plates Adjustable From Medium To XL PALS Webbing On Front And Back For Versatility And Customization Velcro On Front And Back For Id Patch Placement Cummerbund Is Designed To Hold 6” X 6” Side Plates Comfortably Shoulder Pads Included 860 Denier Poly Construction Reinforced Drag Handle  

SPARTAN ARMOR SYSTEMS ® ADVANCED INDIVIDUAL FIRST AID KIT (AFAK)   Product Overview Includes select first aid and trauma tools to handle and treat severe bleeding, airway/respiratory issues, and more. The AFAK features the 600 D Compact IFAK Ripaway Pouch to efficiently store and organize critical life-saving and wound care components and allows the responder to rapidly and reliably address scenarios with the proper products. We highly recommend this kit for LEO/MIL and standard civilian use.    Ability To Respond Being able to assess and address life-threatening injuries and wounds in the field, from minor cuts and abrasions to more extensive life-threatening injuries, is a crucial skill that requires a capable tool-set. The Advanced Individual First Aid Kit (AFAK) by Spartan Armor Systems® was designed to allow operators to be their own first-responder and to attend to colleagues when traumatic scenarios occur. Don’t be caught in a critical moment without the components you need to assist and rescue. The AFAK is a compact kit that can easily be stowed in a vehicle, backpack, locker, and virtually any other easy-access location.    Advanced Individual First Aid Kit (AFAK) Specs and Components: 600 D Compact IFAK Ripaway Pouch WithMolle and Velcro  NAR Combat Application Tourniquet (CAT) in Black Triton Grip SE Nitrile Gloves Large NAR S Rolled Gauze- 4.5 x 4.1 yards NAR Emergency Trauma Dressing- 4" (FLAT) Hyfin Vent Compact Chest Seal Twin Pack Rusch Latex Free Robertazzi 28fr Naso Airway With lube 5.5 EMT Shears Black Handle Survival Rescue Blanket-Compact TCCCC Cards 1 Sharpie Marker

Features: Tri-fold design Multiple pockets and elastic loops for storage Double zipper closure Additional 2" webbing, with pull-tab for quick/temporary closing Two inch patch area across front of pouch Wide handle for carrying or rapid removal Two D-rings on the back for shoulder strap The Condor Rip-Away EMT Pouch The Condor Rip-Away EMT Pouch carries all your 1st aid gear. The pouch is designed to be rip-away from the modular platform when needed, and the strap on the platform keeps it from falling off accidentally. The Rip-Away design gives the ability to utilize the bag in place or "rip" it away for easier access or even to transfer items to another medic. Features of Condor Rip-Away EMT Pouch Tri-fold design Multiple pockets and elastic loops for storage Double zipper closure Additional 2" webbing, with pull-tab for quick/temporary closing Two inch patch area across front of pouch Wide handle for carrying or rapid removal Two D-rings on the back for shoulder strap

The M4 Double Pistol Mag Pouch can fit two M4/M16 mags in EACH pouch. Having the velcro flap will secure your mags and won't go anywhere until you need them.  Each pouch holds 2 M4 Mags Has adjustable hook loop flap Includes grommets for drainage

Condor Singe Flash Bang Mag Pouch Specifications: Overall dimension: 5.25"H x 2.25"W x 2"DMag Capacity:Fits One flashbang (not included)

The Condor Handcuff Case is a compact carrying case that can store up to two pairs handcuffs. The flip-open design features a hook and loop closure for maximum security, while still providing quick access thanks to a pull tab on top that makes opening and closing simple. While it cannot accommodate two sets of ASP cuffs, it can fit one pair of ASP cuffs, one set of Peerless cuffs or two sets of Peerless cuffs, providing you with a versatile case for your load out. Features of Condor Handcuff Case Depth: 1.25" Rugged nylon construction Hook and loop closure Dedicated top pull tab Protective internal divider Can be mounted on a belt or universal webbing Cannot fit two sets of ASP cuffs Can hold either one pair of ASP, one pair of Peerless or two pairs of Peerless cuffs Handcuffs not included

Specifications Holds six M4/M16 mag Adjustable hook & loop flap Import Note: Magazines not included.

This Condor Double Pistol Mag Pouch secures your mags with a reinforced full flap of velcro to ensure your pistol mags aren't going ANYWHERE until you reach for them. Secure your Double Pistol Mag Pouch to your carrier, put your mags in and you are ready for what comes your way. Fits all 9mm, .40, .45 common handgun mags.  

The Condor Sidekick pouch is a low profile, versatile, utility pouch for all your tools, such as allen wrench, mini flashlight, pocket knife, pen, and other accessories. The para-cord creates a 90 degree angle and makes it work station. Features of Condor Side Kick Pouch Fully opens with paracords to adjust One internal pocket Multiple elastic holders One external pocket with zipper closure Webbing over entire pouch for more attachments 3"H x 5"W ID/ Patch panel

SPARTAN ARMOR SYSTEMS® ACHILLES LASER CUT PLATE CARRIER   Product Overview The Achilles Laser Cut Plate Carrier pays homage to the legendary Greek warrior, Achilles, a great hero of the Trojan War. Lightweight, durable, and highly adaptable the Achilles carrier is designed for the modern-day multi-role warrior. Comprised of lightweight 1000 Denier laser-cut Molle and featuring comfortable padded shoulder straps and padded front and rear sections with ventilation vents, Spartan Armor Systems® has also enhanced the capability of the Achilles Laser Cut Plate Carrier by adding our top-zippered admin pouch above a convenient kangaroo pouch that comes with removable triple M4 mag pouches.   Added Comfort And Capability Capability and comfort keep you in the fight longer. The Achilles Laser Cut Plate Carrier will accept both 10"x12" and 11"x14" body armor. For example, to increase comfort and protection it is possible to run our Flex Fused Core IIIA soft armor behind steel core plates such as our III+ AR550 10"x12" body armor utilizing the dual-chamber system! The cummerbund accepts side plates (6”x6” or 6"x8") and is modular/removable, with the inclusion of the built-in 2-inch quick-release straps. The configuration and customization options with the Achilles Laser Cut Plate Carrier are endless. Achilles Laser Cut Plate Carrier Specs:  1000 Denier Materials Lightweight And Duty 1000 Denier Laser Cut Molle Zippered Admin Pouch Kangaroo Pouch With Removable Triple M4 Pouches Padded Shoulder Pads Padded Front And Rear With Ventilation Vents Low Profile Drag Handle Molle Velcro Front And Rear For Identifier Patches 2-inch Replaceable Quick-release Buckles Accepts 10"X12" And 11"X14" Body Armor 6"X6" And 6"X8" Side Plates Fits S To XL

Specifications Mount horizontally on MOLLE Platform Wrap-around design to fit pistol with laser or flashlight mount Retention system with additional hook and loop strap to secure weapon Overall dimensions: 4.25" W x 8" H x 1.5" D Available in: Olive Drab Black Coyote Brown The Condor HT Holster: Specifications Mount horizontally on MOLLE Platform Wrap-around design to fit pistol with laser or flashlight mount Retention system with additional hook and loop strap to secure weapon Overall dimensions: 4.25" W x 8" H x 1.5" D Available in: Olive Drab Black Coyote Brown

Condor Kangaroo Triple Mag Pouch AR/M4 mag compatible Pistol mag compatible with adjustable flap MOLLE compatible Imported Overall dimension: 6"H x 10.5"W x 2.5”D Mag Capacity: Three AR/M4 mags Three pistol mags NOTE: Magazines not included.

Spartan Armor Systems Plate Carrier Bag   The Spartan Armor Plate Carrier bag is an ideal way to keep your Armor ready for transport or stored in your home, vehicle or office.  The bag features Velcro on the front for a nametape or your favorite moral patch.  The back side has molle designed to mount our padded helmet bag (Sold Separately) but will work for any other molle gear your have.  On the inside it has a small zippered pouch.  Keep your gear ready to go, organized and clean with this bag. FEATURES: Two carry options (Handle & MOLLE). 6.5"x3" velcro for patches Zippered interior storage area.

Spartan Armor Padded Helmet Pouch   Are you tired of trying to keep your gear organized? Our Padded Helmet Bag is designed to keep your helmet safe and will attach via molle to Spartan Armor Systems Plate Carrier Bag (Sold Separately).  It will also attach to any other molle gear you may have.  Get protected and organized with Spartan Armor Systems modular Bag and Helmet Bag.   FEATURES: Two carry options (Handle & MOLLE). Accommodates various-size helmets. Zippered interior side storage area.

  FEATURES: Maxx-Dri Technology offers 100% breathability compared to traditional PCs Holds 10x12 Plates Ultra Lightweight Ultra Fast Donning and Doffing Ideal for donning over a Police Uniform Lightning Fast Infinity Adjustment System for a truly Custom Fit Anti-Gravity weight management technology Heavy Duty Mil-spec construction Heavy Duty Genuine YKK buckles and straps Molle and Velcro Molle front and rear Front Velcro for ID patches Heavy Duty Rear Drag/Rescue Handle This plate carrier was designed by 221B Tactical SIZING: One Size Fits All (Adjustable Heavy Duty Genuine YKK Side Release Buckles and Straps)

The Condor G.P. pouch is a great general purpose pouch with front and top zippered pockets for easy storage of essential gear. If you're looking for a way to expand the capabilities of your plate carrier or war belt, the Condor G.P. pouch is an ideal choice.     Features Genuine Crye-Precision MultiCam® MOLLE webbing for modular attachments External zipper pocket Zipper main compartment with mesh sleeve Two 6" MOD straps included MOLLE compatible Overall dimensions: 6.25"W x 7.25"H x 1.5"D

Type a description for this product here...

Our limited edition Betsy Ross patch has arrived! The 13 stars represent the original colonies that won our freedom and independence. Place this patch on your plate carrier, or any Velcro/hook and loop surface!This patch is constructed from durable PVC. The back of the patch has Velcro so it will stick nicely to your rig.  Select your color, select your quantity, and add to cart.  Remember, everything we sell comes with free shipping! Protect What's Yours.... LIKE A SPARTAN!   Patch Dimensions: 2" Circle

The Target Man™ DIY “Do-It-Yourself” AR550 Dueling Tree Target Kit | Extreme High HardnessNEW- AR550 DIY Dueling Tree Target Kit! The AR550 DIY Dueling Tree Target Kit is designed to provide the shooter with extreme wear resistance due to its extreme high hardness. With a 10% increase in hardness, our DIY AR550 Dueling Tree Target Kit is sure to provide you with a lifetime of fun! Though we still rate them to withstand the same abuse as our AR500 Dueling Tree Target Kits, the added hardness provides a little extra “insurance” against and early target fatigue and a definite increase in life expectancy.Please note: The DIY Dueling Tree is designed to save you a ton of money! If you're not a welder, we do offer dueling trees that are already built and ready to go. Please check our reactive target category for the pre-built dueling tree. Absolutely nothing for you to do or source if you go that route.A TTM Original! This is for the “Do-It-Yourselfer” who has access to a welder! Make your own dueling tree at a fraction of the cost compared to purchasing one that is pre-built. Constructed from 3/8″ AR550 ballistic grade steel, these paddles can take some severe abuse! Each AR550 paddle measures 6″ in diameter.  Shoot with any pistol/magnum round from any safe distance (we highly recommend a minimum of 10 yards for maximum safety)! Shoot with high-caliber (ball ammo) center-fire weapons traveling 3200 feet per second (FPS) or less from 100 yards. We have sold thousands of these kits and everyone loves how easy this tree is to build! Angle iron measurements: 4 paddle tree- 46" 6 paddle tree- 66" 8 paddle tree- 84" INCLUDED INSTRUCTIONS! Building this dueling tree is super easy!Optional .22LR Paddles: We have added optional paddles so shooters can use .22LR ammo (assuming you can find it)! Ammo is expensive, so our newly added 1/4″ A36 Hot Rolled Pickled and Oiled (HRPO) paddles are sure to react with this light caliber ammo. Designed for .22 roundsonly. You risk damage to the target should you shoot with higher caliber ammunition!Optional Pivot Tube Upgrade: As an option, we've added BEEFY 1.5″ DOM pivot tubes. The DOM pivot tubes provide extreme resistance to wear and are twice the thickness of our our standard pivot tubes provided with the kit. Your dueling tree will get a lot more life from the additional strength of the thicker walled pivot tubes. Well worth the upgrade!Recommendations: When building your tree, we recommend purchasing 1.5″ angle iron in .25 thickness. The height of the tree is up to you. Also, when welding the angle iron to the base, always have the top of the angle iron leaned toward the shooter, with the “V” facing the shooter as well (to protect the pivot tube). This way gravity will keep the targets to either the left or right position and you won't have to worry about them getting stuck.Don't forget to add our Multi-Purpose Base (MPB). The MPB is configured to accept the angle iron at a 22 degree lean. No guess work on how to set up your tree. Plus, the MPB can be used for ANY of our reactive target systems. Check it out! See A Comparison of Our Full Line Reactive Steel Targets on page 2:

The Target Man™ DIY “Do-It-Yourself” AR500 Dueling Tree Target KitFor the ultimate in longevity, please check out our NEW AR550 DIY Dueling Tree Target Kits. With a 10% increase in core hardness, our AR550 dueling tree kits are sure to be the last DIY tree paddles you purchase.Check them out here!Please note: The DIY Dueling Tree is designed to save you a ton of money! All components fit in to a flat rate box from the post office. If you’re not a welder, we do offer dueling trees that are already built and ready to go. Please check our reactive target category for the pre-built dueling tree Absolutely nothing for you to do or source if you go that route.A TTM Original! This is for the “Do-It-Yourselfer” who has access to a welder! Make your own dueling tree at a fraction of the cost of purchasing one that is pre-built. Constructed from 3/8″ AR500, these paddles can take some severe abuse! Shoot with any pistol/magnum round from any safe distance! Shoot with high-caliber (lead only) center-fire weapons traveling 3200 FPS (or ANY pistol from any SAFE distance) or less from 100 yards. We have sold thousands of these kits and everyone loves how easy this tree is to build!   Angle iron measurements: 4 paddle tree- 46" 6 paddle tree- 66" 8 paddle tree- 84" INCLUDED INSTRUCTIONS!NEW ~ We have added optional paddles so shooters can use .22LR ammo! Ammo is expensive, so our newly added 1/4″ A36 Hot Rolled Pickled and Oiled (HRPO) paddles are sure to react with this light caliber ammo. Designed for .22 rounds only. You risk damage to the target should you shoot with higher caliber ammunition! When you select “add .22 paddles”, we’ll make sure you receive the correct amount of .22 paddles for your kit size selection.All kits come with de-burred pivot tubes. You will receive the correct amount of tubes depending on which configuration of paddle targets you order. Keep in mind, if you order kits with both AR500 paddles and .22 paddles, you’ll only receive 1 set of tubes. The idea is to make these paddles interchangeable. Swap paddles depending on the ammunition you are shooting!Optional Pivot Tube Upgrade: As an option, we’ve added BEEFY 1.5″ DOM pivot tubes. The DOM pivot tubes provide extreme resistance to wear and are twice the thickness of our our standard pivot tubes provided with the kit. Your dueling tree will get a lot more life from the additional strength of the thicker walled pivot tubes. Well worth the upgrade!Recommendations: When building your tree, we recommend purchasing 1.5″ angle iron in .25 thickness. The height of the tree is up to you. Also, when welding the angle iron to the base, always have the top of the angle iron leaned toward the shooter, with the “V” facing the shooter as well (to protect the pivot tube). This way gravity will keep the targets to either the left or right position and you won’t have to worry about them getting stuck.Don’t forget to add our Multi-Purpose Base (MPB). The MPB is configured to accept the angle iron at a 22 degree lean. No guess work on how to set up your tree. Plus, the MPB can be used for ANY of our reactive target systems. Check it out! See A Comparison of Our Full Line Reactive Steel Targets on page 2:

The Target Man™ Angle IronHere we have angle iron as an option, but we highly suggest NOT buying it from us. You can source it locally for about $5-10/piece. The shipping is killer, which is why we have to charge so much. You MUST use 1.5″ x .25 American-spec (standard type) angle iron. Available at most home improvement stores or any steel yard.   Please Note: This is the only the Angle Iron  See A Comparison of Our Full Line Reactive Steel Targets on page 2:

AR500 Hanging Targets Also available in Mild Steel See A Comparison of Our Full Line Reactive Steel Targets on page 2:

The Target Man™ AR500 Gong Target – Round Circular Gong Target 3/8″ AR500 Mounting holes are approximately .5″ “Select Options” to choose target size. See A Comparison of Our Full Line Reactive Steel Targets on page 2:

The Target Man™ DIY “Texas Walker” – Reactive Flipping Target“DIY” Texas Walker!– No matter what, you always have a shot at any one of the upright paddles. Draw a start/finish line in the sand, place the targets on the floor, and compete with your buddies to see who crosses the finish line first TONS of fun!This kit is CNC cut from 3/8″ AR500. Each paddle measures 3″(small) or 4.5” (large) in diameter. This kit comes un-welded! The picture is for reference only to show you what a welded walker looks like. See A Comparison of Our Full Line Reactive Steel Targets on page 2:

The Target Man™ DO-IT-YOURSELF “DIY” AR500 PLATE RACK  Gen IIIWhy are plate racks so expensive? Because they’re bulky and cumbersome to ship! The Target Man™ has come up with an inexpensive, innovative solution. If you weld, or know someone who does, you can find tremendous savings by purchasing our DIY plate rack.  You simply have to source some steel, and we’ll supply the AR500 targets, pivot brackets, levers, and the resetting mechanism.In our latest version, we took into consideration, value, ease of assembly, and above all quality.  The Target Man™ has sold hundreds of these plate rack kits due to the tremendous value and savings offered.Please see the list below to determine what you’ll need to purchase.  Please note that we do NOT supply instructions without a purchase. We simply give you the list of items you’ll need to procure locally. Once you purchase you will receive detailed instructions on assembly. Items you need to source… 1.5″x.25″ angle iron cut to 3.5 feet for the legs 3″x.25″ angle iron cut to 66″ for the main body 1″ OD tubing cut to about 70″ 4″x .5″ Flat Bar cut to approximately 70″     See A Comparison of Our Full Line Reactive Steel Targets on page 2:

The Target Man™ 1/2″ AR500 Gong Targets Gong Targets cut from 1/2″ AR500!These targets are engineered to last. All of our targets are laser cut for precision. With our 1/2″ AR500 shooting targets, you will be sure to get tens of thousands of impacts from high-power center-fire weapons. Customers have used our 1/2″ AR500 for 338 Lapua and 50 BMG.Please note the 6″ and 8″ targets only have 2 mounting holes. The 10″ and 12″ targets have 3 mounting holes (as pictured).   See A Comparison of Our Full Line Reactive Steel Targets on page 2:

The Target Man™ DIY "Heads Up” AR500 Reactive Steel Shooting Target DIY "Heads Up” is a reactive target system constructed from ballistic grade AR500. DIY "Heads Up" doubles as a pertinent target head shot and gut shot target aid…. both of which are essential impact points for self defense. Perfect for the LEO, gun enthusiast, and even the recreational weekend “plinker”. Get one of the best training aids to sharpen your skills should you ever need to take that “critical shot”.This kit is available in a few different configurations for all budget levels. DIY "Heads Up” is available with or without our patent-pending Multi-Purpose Base (MPB) and .22 Mild Steel Paddle. The DIY "Heads Up” is un-welded, but don’t worry as assembly is as easy as 1-2-3: (1) Assemble slotted “throat” (aka target holding fixture) like a puzzle using the slotted/tabbed pieces. Ensure all pieces are “square”. (2) Tack the kit into position with your welder. (3) Start welding!Our setup is designed to be used with 1.5″x.25″ angle iron. We sell all of our reactive targets without the angle iron. You can source it locally for $12-$15, or you can buy it separately in the Replacements and Add on section of this site. It’s a more expensive option simply due to the shipping cost. Remember, we want to make this target kit affordable for all budgets. If possible we recommend you source it locally.Target Specifications….. Target height: 19.5″ Target width: 12″ Center hole of target diameter: 4.5 Center hole reactive paddle diameter: 6″ Hostage reactive paddle width: 5″ We recommend using 46" angle iron for his target.   This is basically a 2/3 scale IPSC   See A Comparison of Our Full Line Reactive Steel Targets on page 2:

The Target Man™ DIY Head Shot Gut Shot (HSGS) – AR500 Reactive Steel Shooting TargetHead Shot Gut Shot (HSGS)!! 4-stage reactive target system constructed from ballistic grade AR500. This four way target system is perfect for someone to enhance their tactical shooting skills. Here you have a head shot, gut shot, center mass shot, and a tactical “slap paddle” (to reset the center mass target)! Perfect for the LEO, gun enthusiast, and even the recreational weekend “plinker”. Get one of the best training aids to sharpen your skills should you ever need to take that “critical shot”.This kit is available in a few different configurations for all budget levels. This kit is a DIY un-welded version. You have the option to purchase it  with and without the our patent-pending Multi-Purpose Base (MPB) and you can also purchase this kit welded and ready to go in our Reactive Steel Target section. Save some decent coin by purchasing the un-welded kit and fab up your own base. If you’re purchasing the kit un-welded, don’t worry as assembly is as easy as 1-2-3. (1) Assemble slotted “throat” (aka target holding fixture) like a puzzle using the slotted/tabbed pieces. Ensure all pieces are “square”. (2) Tack the kit in to position with your welder. (3) Start welding!Our setup is designed to be used with 1.5″x.25″ angle iron. We sell all of our reactive targets without the angle iron. You can source it locally for $12-$15, or you can buy it separately in the Replacements and Add on section of this site. It’s a more expensive option simply due to the shipping cost. Remember, we want to make this target kit affordable for all budgets. If possible we recommend you source it locally. Target Specifications….. Target height: 19.5″ (with head in up position) Target width: 12″ Target comes unpainted. We recommend using 46" angle iron for his target.   This is basically a 2/3 scale IPSC See A Comparison of Our Full Line Reactive Steel Targets on page 2:

The Target Man™ CRITICAL SHOT – Reactive AR500 Steel Shooting TargetNamed by AR15.com member Jeffco55! The Target Man Critical Shot is a 2-stage reactive target system constructed from ballistic grade AR500. Critical shot doubles as a hostage target and a center-mass shot. Perfect for the LEO, gun enthusiast, and even the recreational weekend “plinker”. Get one of the best training aids to sharpen your skills should you ever need to take that “critical shot”. This kit is available in a few different configurations for all budget levels. This version is the the pre-welded assembly that comes with a throat. This kit is available with and without the our patent-pending Multi-Purpose Base (MPB) and you can also purchase this kit un-welded in our DIY Shooting Target section. Save by purchasing the un-welded kit and fab up your own base.  Our setup is designed to be used with 1.5″x.25″ angle iron. We sell all of our reactive targets without the angle iron. You can source it locally for $12-$15, or you can buy it separately in the Replacements and Add on section of this site. It’s a more expensive option simply due to the shipping cost. Remember, we want to make this target kit affordable for all budgets. If possible we recommend you source it locally.Target Specifications….. Target height: 19.5″ Target width: 12″ Center hole of target diameter: 4.5 Center hole reactive paddle diameter: 6″ Hostage reactive paddle width: 5″ We recommend using 46" angle iron for his target.   This is basically a 2/3 scale IPSC   See A Comparison of Our Full Line Reactive Steel Targets on page 2:

The Target Man™ DIY “Hostage Moe” – AR500 Reactive Hostage Shooting Target“Hostage Moe” is a 66% IPSC shooting target with a reactive hostage head location. Constructed from ballistic grade AR500, this target is sure to provide years upon years of enjoyment. Whether you’re a competition shooter, recreational shooter, or even LEO, this target is sure to hone your skills and provide hours of enjoyment.This target system is available in a few different variations. You can purchase either the do-it-yourself (DIY) target system, or you can have us do all the welding for you. The welding is super easy and we provide instructions for the reactive throat. The reactive throat is what holds your target to the angle iron and it positions your target at the optimal 22 degree angle, which safely deflects bullet fragments down upon impact. This product is a DIY target. You will receive an un-welded target and throat assembly.  Our setup is designed to be used with 1.5″x.25″ angle iron. We sell all of our reactive targets without the angle iron. You can source it locally for $12-$15, or you can buy it separately in the Replacements and Add on section of this site. It’s a more expensive option simply due to the shipping cost. Remember, we want to make this target kit affordable for all budgets. If possible we recommend you source it locally.Also, if you don’t already have one, you may want to consider our patent-pending multi-purpose base (MPB). The MPB works great for all of our reactive target systems, plus you can also use it for our dueling tree target systems. There are two angle insertion slots – one that holds the angle iron in the vertical position for use with our reactive target systems, and one that holds the angle iron at a 22 degree lean for our dueling tree target systems.Specifications                                      12″(W) x 20″(H)     Ballistic grade 3/8″ AR500     Weight – Approximately 22 lbs.     Target comes unpainted.     DIY kit includes un-welded throat, un-welded target, pivot tube, reactive hostage paddle, and instructions for throat     Welded kit includes pre-welded throat, pre-welded pivot tube, and reactive hostage paddle     OPTIONAL angle iron is approximately 4 ft. (+/- a couple of inches). You MUSTused 1.5″x.25″ angle for this to work! We recommend using 46" angle iron for his target.   OPTIONAL: Multi-Purpose Base specifications can be found here.  See A Comparison of Our Full Line Reactive Steel Targets on page 2:

The Target Man™ 3/8 AR500 IPSC & “D” Shaped Gong PackageIPSC / 12″ / 10″ / 8″ Target Bundle KitBuy in bulk and save! By purchasing this item, you will receive (1) 12″, (1) 10″, (1) 8″, and (1) 1/2 Scale IPSC(9″x13.6″) AR500 targets! Constructed from 3/8″ AR500, these targets are sure to last! See A Comparison of Our Full Line Reactive Steel Targets on page 2:

Heads Up Replacement Paddles See A Comparison of Our Full Line Reactive Steel Targets on page 2:

Head Shot Gut Shot Replacement Paddles           See A Comparison of Our Full Line Reactive Steel Targets on page 2:

Critical Shot Replacement Paddles           See A Comparison of Our Full Line Reactive Steel Targets on page 2:

Challenge Tree Paddle   3/8″ AR500 paddles with 4″ paddle face.      See A Comparison of Our Full Line Reactive Steel Targets on page 2:

The Target Man™ 3/8” AR500 “D” Shaped Gong Package 6″ / 8″ / 10″/12" Gong Target Package “D” Shaped. Buy in bulk and save! By purchasing this item, you will receive (1) 6″, (1) 8″, (1) 10″ and (1) 12" AR500 targets! Constructed from 3/8″ AR500, these targets are sure to last! See A Comparison of Our Full Line Reactive Steel Targets on page 2:

The Target Man™ .22 LR PaddlesBought an AR500 dueling tree kit from us and want to use the cheapest ammo possible? TTM has solved your problem! We now offer a .22LR “retrofit” kit for our DIY dueling trees. Simply remove your AR500 dueling tree paddles and drop these in. Perfect for .22LR all day long!Please remember these are A36 mild steel paddles and NOT AR500! Heavier caliber weapons WILL damage your targets!5.5″ diameter paddles. Choose your configuration below. See A Comparison of Our Full Line Reactive Steel Targets on page 2:

Backpack Armor -  Spartan Armor Systems™ Flex Fused Core™ IIIA Soft Armor 11" x 14" Panel Due to popular demand, we have developed our own version of pistol rated level IIIA soft armor which is now available in single 11" x 14" panels to function as inserts for backpacks or similar applications. As it's name implies, the Spartan Armor Systems™ Flex Fused Core™ Soft Armor flexible and easily forms to most properly sized backpack chambers. Keeping with Spartan Armor tradition, it offers GREAT protection at a GREAT price. Composed of only the best American made materials and proudly assembled in our new state of the art facility in Tucson, Arizona.   Rated to stop .44 MAG SJHP, as well as Special Threat Rated to stop .357 SIG FMJ  This soft armor can be used stand alone, giving level IIIA protection or ICW (in conjunction with) as backer on any hard armor systems. Multi-hit rated to stop 6 rounds All parts of this product are proudly American made. Thinness: .35" profile Weight: 1lb 9.4 oz Includes One  (1) 11"x14" Panel

Spartan Armor Systems Armis Level IIIA Multi Curve Plates Spartan Armor Systems has had a lot of customers ask for combination threat level IIIA plates. What is a combination threat level plate? A combination threat level plate is a plate that is stab-resistant as well as bullet-resistant. The plates have a multi curvature to conform to the body for improved comfort. Our Spartan Armis Level IIIA Plates are coated/encapsulated with Spartan Armor Systems proprietary “Encapsaloc” Polyurea Coating. Along with a raised, embedded, and 3D Spartan Armor Systems Logo the “Armis” Plates set the standard for those looking for level IIIA Body Armor at an affordable price.    Two (2) Body Armor Plates Are Included With Each Order. These Plates come with a 5-year warranty and a 5-year shelf life! Specifications: Stand-Alone Armor System 10” X 12” 1.5 lbs/plate Multi-Shot Rated 3/8” profile Our Proprietary “Encapsaloc” Polyurea Coating Multi-Curve Ergonomic Design Stab Resistant Raised and Embedded 3D Spartan Armor Systems Logo     Export Administration Regulations (EAR) and International Traffic in Arms Regulations (ITAR) - US Export Regulations: Level III and IV rifle rated body armor (Rifle Plates) fall under jurisdiction of the Export Administration Regulations (EAR) and International Traffic in Arms Regulations (ITAR), and are subject to the export control laws of the US Government. Export or re-transfer of Rifle Plates by any means to any foreign end user or for any other end use, whether in the US or abroad without written approval of the US Department of Commerce or Department of State is prohibited. The sale, transfer, transportation, or shipment outside of the US of any product prohibited or restricted for export without complying with US export control laws and regulations, including proper export licensing, documentation or authorization, is strictly prohibited and may result in civil penalties and/or constitute a federal crime. Spartan Armor Systems, TK Armor Systems, LLC will not engage in any transaction that requires the illegal export of any products and will not assist directly or indirectly with the illegal export or re-export of any products.