Made in the USA

Your choice of Level III AR500 or Lightweight Level III+ steel core armor plates. Tactical Scorpion Gear AR500 steel core armor .(Made in the USA) A stand alone armor plate with multiple hit capability We only manufacture our plates from certified AR-500 steel with a Brinnell Hardness Rating of505-518BHN Laser cut Fully tested by independent Lab Rated for up to six hits from 7.62 Nato bullets (.308 Winchester) with velocities up to 2780 fps Tactical Scorpion Gear Level III+ steel plate armor . (Made in the USA) We are Compliant with all NIJ standards so dont pay more for lesser quality products. A stand alone armor plate with multiple hit capability - passed NIJ 0101.06 6 shot stand alone tests against 5.56 M855 M80 ball (greentip) at 2800fps and 5.56 M193 55 Grain FMJ at 2900fps. In house testing defeated 30-06 165 grain copper tip trophy. Listed on the Department of Justice NIJ certification website. Level 3+ plates are manufactured from a proprietary steel reaching Brinnell Hardness ratings in 600 - 630 Laser cut Simply Stronger, Thinner and lighter than the competition Our new proprietary steel core is far stronger than the AR500 - AR650 steel core. This core is hardened all the way through unlike the AR500 - AR650 which is only surfaced hardened. At only 0.197 inches thick nominal makes it 20% lighter than the AR500 and superior in strength. Our build-up spall coating is done with a Graco EXP-2 which is the top of the line high pressure heated coating system. Our plate core is chemically washed and etched on the strike surface to eliminate the coating from delaminating when shot which keeps the shrapnel from escaping from the armored assembly Tactical Scorpion Gear 10 mm Trauma Pad Custom made , computer cut on triple axis CNC router machine to perfectly match our armor plate Will absorb the impression of any projectile impact onto the armor plate protecting your ribs from the compression ** This model complies with NIJ Standard-0101.06 for Ballistic resistance of Body Armor.** We utilize a CNC laser cutting table for the cutting of all our Steel core products. If the seller of armor plate does not mention how its cut, then you can guarantee its not by laser There is no equal method Plasma cutting cuts slowly, this puts a lot of heat into the steel. ( Submerged plasma cutting machine is no better) This excess heat can result in excessive chipping and damage near the cut edge during use and easily shattering when shot. Plasma cutting generates large amounts of heat that is deposited into the target, softening it's edges. The heat-affected zone (HAZ) generated by plasma cutting is the largest out of the most commonly used methods for cutting abrasion resistant steel. Most AR500 is cut with plasma cutters as they are cheap and relatively small compared to other methods. Here at Tactical Scorpion Gear we manufacture our own vest carriers, Kevlar level IIIA vests and all our products. We have every item listed Available and ready for immediate shipping. Tested by HP White laboratory ** This model complies with NIJ Standard-0101.06 for Ballistic Resistance of Body Armor.** NIJ tested Level III Armor will defeat 6 rifles round shots up to 7.6251/.308 @ 2780 ft/s @ 15 METERS Level III+ lightweight base coated 6x6: 33 ounces 6x8: 44 ounces 8x10: 70 ounces 10x12: 103 ounces 10x12 modified: 88 ounces 11x14: 138 ounces Level III AR500 base coated 6x6: 42 ounces 6x8: 53 ounces 8x10: 83 ounces 10x12: 126 ounces 10x12 modified: 115 ounces 11x14: 178 ounces Level III+ lightweight spall coated 6x6: 39 ounces 6x8: 52 ounces 8x10: 80 ounces 10x12: 119 ounces 10x12 modified: 104 ounces 11x14: 157 ounces Level III AR500 spall coated 6x6: 47 ounces 6x8: 64 ounces 8x10: 98 ounces 10x12: 150 ounces 10x12 modified: 129 ounces 11x14: 204 ounces

Proudly made in the U.S.A AR550 Level III+ Steel Body Armor Panel Ergonomic Multi-Curve design at no extra cost Powder Coated finish to protect steel from the elements Shooters Cut Rated and tested to: NIJ STD-0101.06 Level III and also special threats listed NIJ STD-0101.07 Draft RF2 Emergency drag handle Removable low profile shoulder pads Adjustable shoulder straps MOLLE webbing for modular attachments Hook and loop webbing Front map pocket with snap, hook and loop closure Breathable 3D Mesh liner Adjustable cummerbund with built-in soft armor pockets Side release buckles Easy access plate pockets Ballistic plates/soft armor not included Imported Caliber Armor AR550 Level III+ Body Armor And Condor MOPC Gen II Package AR550 Level III+ Steel Body Armor Panel Ergonomic Multi-Curve design at no extra cost Powder Coated finish to protect steel from the elements Shooters Cut Rated and tested to: NIJ STD-0101.06 Level III and also special threats listed NIJ STD-0101.07 Draft RF2 Proudly made in the U.S.A We have gone above and beyond to bring you steel body armor of a HIGHER CALIBER. This can be seen with our bend process, our fragmentation coating and our finishing details. This was the material that we started from and have the most experience with. We’ve seen it, done it, we’ve improved it. Steel Body Armor provides great protection that can stop multiple projectile hits. We have been working with different levels of abrasion resistant (AR) ballistic steel for years and have not found a better product than our AR550 Steel Body Armor Plates. This armor is rated at a level III+ as it can defeat special threats like M855 rounds. All of our steel plates come in one ergonomic curve option. We have worked with LE and first responders to design a curve that you can be comfortable wearing. We provide this at no additional cost. What is unique about the way that we bend our steel is important too. We have designed a press that creates a multi curve bend in ONE step. Why is this important? When you do multiple bends to achieve a multi curve, it puts extra strain on the plate which can weaken it. We have replicated the same curves that you have seen in multi curve ceramic armor for years. Our aggressive Shooters Cut body armor plates shaves off weight while still providing enough coverage to protect your vital organs. Use our CaliberX™ Soft Armor Backers for even more protection and comfort. Our standard AR550 plate comes coated to protect the plate from rust and the elements. One concern with Steel Armor is fragmentation containment. Some of that fragmentation is contained in the armor’s plate carrier, but there still is a risk of lethal shrapnel. We HIGHLY recommend our Caliber Anti-Spall add on. We have teamed up with our friends at Bullet Liner® to formulate an anti-spall coating specifically for our armor application. This addition to your steel plate gives you peace of mind when wearing steel armor. Weights for AR550 Steel Body Armor: 10 x 12 – 8lb 13 oz with Anti-Spall Coating NIJ STANDARD-0101.06 Tested and verified to meet or exceed ballistic resistance as specified under NIJ Standard- 0101.06 Level III and also special threats tested included in the draft NIJ Standard- 0101.07 RF2. MANUFACTURING TOLERANCES: Thickness dimensions are +-1/8 in. Width and length dimensions are +0.00 to 0.25 in. All weights are +- 5%. Modular Operator Plate Carrier (MOPC) Gen II Caliber Armor offers the Modular Operator Plate Carrier (MOPC) Gen II by Condor Outdoor because it one of the highest selling plate carriers on the market. For good reason, as it is widely used by law enforcement throughout our country. It is designed for modular attachments with MOLLE webbing on all sides as for functionality and operator mobility. The MOPC accepts Caliber Armor AR550 Steel Body Armor Plates in both 10” x 12” and 11” x 14”. If you are purchasing thicker composite/ceramic plates it accommodates 10”x 12” sizes. This plate carrier allows you to either use the full cummerbund or the internal waist strap for a scaled down system when needed. Features Emergency drag handle Removable low profile shoulder pads Adjustable shoulder straps MOLLE webbing for modular attachments Hook and loop webbing Front map pocket with snap, hook and loop closure Breathable 3D Mesh liner Adjustable cummerbund with built-in soft armor pockets Side release buckles Easy access plate pockets Ballistic plates/soft armor not included Imported Cummerbund Size: Adjustable from 40″ – 48″ (measure around your navel) Accepts Caliber Armor AR550 Steel Plates in 10″ x 12″ and 11″x 14″ or any other ESAPI sizes up to 10.25″ x 13.25 Side plate capacity compatible with our CaliberX IIIA soft armor. This is a great option for side protection for a fraction of the weight. Available in:OD GreenBlackCoyote BrownScorpion OCP

AR550 Level III+ Steel Body Armor Panel Ergonomic Multi-Curve design at no extra cost Special Bullet Liner® Anti-Spall Coating Shooters Cut Rated and tested to: NIJ STD-0101.06 Level III and special threats listed in NIJ STD-0101.07 Draft Rifle 2 Proudly made in the U.S.A Features Emergency drag handle Removable anti-slip shoulder pads, with hook and loop guides Adjustable shoulder straps MOLLE webbing for modular attachments Hook and loop webbing Breathable 3D Mesh liner Quick release buckles Easy access plate pockets Accepts Caliber Armor AR550 Steel Plates in 10″ x 12″ Size: : Adjustable sizing from 32″ – 54″ waist size Available in:OD GreenBlackCoyote BrownScorpion OCP Caliber Armor AR550 Level III+ Active Shooter Response Package With Spall Coat AR550 Level III+ Steel Body Armor Panel Ergonomic Multi-Curve design at no extra cost Special Bullet Liner® Anti-Spall Coating Shooters Cut Rated and tested to: NIJ STD-0101.06 Level III and special threats listed in NIJ STD-0101.07 Draft Rifle 2 Proudly made in the U.S.A We have gone above and beyond to bring you steel body armor of a HIGHER CALIBER. This can be seen with our bend process, our fragmentation coating and our finishing details. This was the material that we started from and have the most experience with. We’ve seen it, done it, we’ve improved it. Steel Body Armor provides great protection that can stop multiple projectile hits. We have been working with different levels of abrasion resistant (AR) ballistic steel for years and have not found a better product than our AR550 Steel Body Armor Plates. This armor is rated at a level III+ as it can defeat special threats like M855 rounds. All of our steel plates come in one ergonomic curve option. We have worked with LE and first responders to design a curve that you can be comfortable wearing. We provide this at no additional cost. What is unique about the way that we bend our steel is important too. We have designed a press that creates a multi curve bend in ONE step. Why is this important? When you do multiple bends to achieve a multi curve, it puts extra strain on the plate which can weaken it. We have replicated the same curves that you have seen in multi curve ceramic armor for years. Our aggressive Shooters Cut body armor plates shaves off weight while still providing enough coverage to protect your vital organs. Use our CaliberX™ Soft Armor Backers for even more protection and comfort. Our standard AR550 plate comes coated to protect the plate from rust and the elements. One concern with Steel Armor is fragmentation containment. Some of that fragmentation is contained in the armor’s plate carrier, but there still is a risk of lethal shrapnel. We HIGHLY recommend our Caliber Anti-Spall add on. We have teamed up with our friends at Bullet Liner® to formulate an anti-spall coating specifically for our armor application. This addition to your steel plate gives you peace of mind when wearing steel armor. Weights for AR550 Steel Body Armor: 10 x 12 – 8lb 7 oz with Anti-Spall Coating NIJ STANDARD-0101.06 Tested and verified to meet or exceed ballistic resistance as specified under NIJ Standard- 0101.06 Level III and also special threats listed in the New NIJ Standard- 0101.07 (Draft) Rifle 2. MANUFACTURING TOLERANCES: Thickness dimensions are +-1/8 in. Width and length dimensions are +0.00 to 0.25 in. All weights are +- 5%. Sentry Plate Carrier Caliber Armor offers the Sentry Plate Carrier by Condor Outdoor because it one of the highest selling plate carriers on the market. For good reason, as it is widely used by law enforcement throughout our country. It is designed for modular attachments with quick release and cinch buckles. This carrier accepts Caliber Armor AR550 Steel Body Armor Plates in  10” x 12”. This package is is perfect for rapid response situations or to add to your workout routine. Features Emergency drag handle Removable anti-slip shoulder pads, with hook and loop guides Adjustable shoulder straps MOLLE webbing for modular attachments Hook and loop webbing Breathable 3D Mesh liner Quick release buckles Easy access plate pockets Accepts Caliber Armor AR550 Steel Plates in 10″ x 12″ Size: : Adjustable sizing from 32″ – 54″ waist size Available in:OD GreenBlackCoyote BrownScorpion OCP

Premium Materials: The lightweight, ergonomic, and modular Shellback Tactical Banshee Elite Plate Carrier features the latest design in armor carriers. Cordura nylon is abrasion and tear-resistant, yet it weighs less than most traditional carriers. Durable: This plate carrier features a  MOLLE platform on the front, back and cummerbund for storing your gear. It's durable, lightweight, and powerful. Unmatched Comfort: Lightweight yet durable, this 3D mesh armor plate carrier is made from military-grade Cordura nylon, with ergonomically placed cummerbunds to increase comfort and reduce fatigue. Perfect Fit: The slim and lightweight shellback tactical banshee elite 3.0 plate carrier is a high-quality piece that fits comfortably and can be adjusted to fit users of all sizes and shapes. Quality Guarantee: The Banshee Elite 3.0 Plate Carrier is proudly made in the USA and backed by a lifetime warranty. Practical and stylish, the Banshee Elite 3.0 has a unique design that's perfect for special forces and military operations. Its lightweight construction with an extendable drag handle along with the laser-cut MOLLE webbing make it the perfect gear for any special operator. Get yours today! Shellback Tactical Banshee Elite 3.0 Plate Carrier Shellback Tactical Banshee Elite 3.0 Plate Carrier is one of the best plate carriers you can get. Period. It's super light and durable, crafted with an extendable drag handle and laser-cut Molle webbing that makes this plate carrier the premium choice for professionals like SWAT, military, and law enforcement. Why get yours? Premium Materials: The lightweight, ergonomic, and modular Shellback Tactical Banshee Elite Plate Carrier features the latest design in armor carriers. Cordura nylon is abrasion and tear-resistant, yet it weighs less than most traditional carriers. Durable: This plate carrier features a MOLLE platform on the front, back and cummerbund for storing your gear. It's durable, lightweight, and powerful. Unmatched Comfort: Lightweight yet durable, this 3D mesh armor plate carrier is made from military-grade Cordura nylon, with ergonomically placed cummerbunds to increase comfort and reduce fatigue. Perfect Fit: The slim and lightweight shellback tactical banshee elite 3.0 plate carrier is a high-quality piece that fits comfortably and can be adjusted to fit users of all sizes and shapes. Quality Guarantee: The Banshee Elite 3.0 Plate Carrier is proudly made in the USA and backed by a lifetime warranty. Practical and stylish, the Banshee Elite 3.0 has a unique design that's perfect for special forces and military operations. Its lightweight construction with an extendable drag handle along with the laser-cut MOLLE webbing make it the perfect gear for any special operator. Get yours today! The Shellback Tactical Banshee Elite 3.0 Plate Carrier is the third evolution of the world famous Banshee Elite plate carrier. The Banshee Elite 3.0 plate carrier is packed with new upgrades such as quick release cummerbund buckles, laser cut Molle and a extendable drag handle.  The new laser cut Molle design is located on the front, rear and cummerbund which reduces carrier weight and increases durability.  The new quick release cummerbund buckles allow you to quickly don and doff your carrier and eliminates the hassle of dealing with traditional hook and loop cummerbund closures.  The new drag handle extends to 34 inches which allows extra leverage when removing a casualty on the battle field. The Banshee Elite 3.0 Plate Carrier is proudly made in the USA and backed by a lifetime warranty. Be ready for the fight and order your Shellback Tactical Banshee Elite 3.0 Plate Carrier today!  Banshee Elite 3.0 Features  Laser cut Molle platform on front, rear and cummerbund reduces weight and adds durability  Two quick release cummerbund buckles to quickly don and doff plate carrier  Rear drag handle extends up to 34 inches in length Constructed of durable 500 denier Cordura nylon Plate pockets load from the bottom hold 10 x 12 shooter or SAPI cut plates Two Shoulder buckles allow quick adjustments to raise or lower plate carrier for the perfect fit 3D Spacer mesh padding on front, rear and shoulder pads for ventilation and comfort Cummerbund features 6 integrated M4 magazine pockets Cummerbund features 2 pockets to insert Banshee Elite 3.0 soft armor panels  Cummerbund features interior laser cut Molle panels to attach side armor plate pockets Front zipper admin pouch for small field gear such as notepads, pens and multitools Rear hydration pocket holds 2L hydration bladder Integrated nylon vertical strips to accommodate QASM buckles for chest rigs  Loop panels on front and rear for ID placards  Lifetime warranty  Made in the USA  Berry Compliant  Banshee Elite 3.0 Sizing  Plate pockets load from the bottom and accept up to 10 x 12 shooter or SAPI cut plates  2 Shoulder buckles allow for quick adjustment to raise or lower plate carrier for the perfect fit  Cummerbund comes in 2 sizes  Small/Medium - 32 inches to 39 inches Large/XLarge - 39 inches to 46 inches  How to Select a Size  Measure the circumference of your body where the bottom of your plate would sit on your torso  Take the measurement and add 2 inches to get your final measurement  Use your final measurement to select from the sizing chart above 

Product Description This MOLLE medical pouch releases from its rear panel with rip-cord handle for easy and instant access to contents. Tactical first aid bag for use when quick, one-hand deployment is critical...• Constructed of 1000 denier nylon• Heavy-duty #9 YKK zipper• Elastic tie downs and internal pocket keep contents of tactical medical pouch organized and secure• Medical pouch for duty belt is available in black, coyote tan, and multicamFirst Aid Belt Pouch DIMS: 6" x 5" x 2.75"

AR550 Level III+ Steel Body Armor Panel Ergonomic Multi-Curve design at no extra cost Special Bullet Liner® Anti-Spall Coating Shooters Cut Rated and tested to: NIJ STD-0101.06 Level III and special threats from NIJ STD-0101.07 Draft Rifle 2 Proudly made in the U.S.A Features Emergency drag handle Removable low profile shoulder pads Adjustable shoulder straps MOLLE webbing for modular attachments Hook and loop webbing Front map pocket with snap, hook and loop closure Breathable 3D Mesh liner Adjustable cummerbund with built-in soft armor pockets Side release buckles Easy access plate pockets Ballistic plates/soft armor not included Imported Available in:OD GreenBlackCoyote BrownScorpion OCPBlack Multi-Cam Caliber Armor AR550 Level III+ Body Armor With Spall Coat And Condor MOPC Gen II Package AR550 Level III+ Steel Body Armor Panel Ergonomic Multi-Curve design at no extra cost Special Bullet Liner® Anti-Spall Coating Shooters Cut Rated and tested to: NIJ STD-0101.06 Level III and special threats from NIJ STD-0101.07 Draft Rifle 2 Proudly made in the U.S.A We have gone above and beyond to bring you steel body armor of a HIGHER CALIBER. This can be seen with our bend process, our fragmentation coating and our finishing details. This was the material that we started from and have the most experience with. We’ve seen it, done it, we’ve improved it. Steel Body Armor provides great protection that can stop multiple projectile hits. We have been working with different levels of abrasion resistant (AR) ballistic steel for years and have not found a better product than our AR550 Steel Body Armor Plates. This armor is rated at a level III+ as it can defeat special threats like M855 rounds. All of our steel plates come in one ergonomic curve option. We have worked with LE and first responders to design a curve that you can be comfortable wearing. We provide this at no additional cost. What is unique about the way that we bend our steel is important too. We have designed a press that creates a multi curve bend in ONE step. Why is this important? When you do multiple bends to achieve a multi curve, it puts extra strain on the plate which can weaken it. We have replicated the same curves that you have seen in multi curve ceramic armor for years. Our aggressive Shooters Cut body armor plates shaves off weight while still providing enough coverage to protect your vital organs. Use our CaliberX™ Soft Armor Backers for even more protection and comfort. Our standard AR550 plate comes coated to protect the plate from rust and the elements. One concern with Steel Armor is fragmentation containment. Some of that fragmentation is contained in the armor’s plate carrier, but there still is a risk of lethal shrapnel. We HIGHLY recommend our Caliber Anti-Spall add on. We have teamed up with our friends at Bullet Liner® to formulate an anti-spall coating specifically for our armor application. This addition to your steel plate gives you peace of mind when wearing steel armor. Weights for AR550 Steel Body Armor: 10 x 12 – 8lb 7 oz with Anti-Spall Coating NIJ STANDARD-0101.06 Tested and verified to meet or exceed ballistic resistance as specified under NIJ Standard- 0101.06 Level III and also tested for special threats listed on the new draft NIJ Standard- 0101.07 RF2. MANUFACTURING TOLERANCES: Thickness dimensions are +-1/8 in. Width and length dimensions are +0.00 to 0.25 in. All weights are +- 5%. Modular Operator Plate Carrier (MOPC) Gen II Caliber Armor offers the Modular Operator Plate Carrier (MOPC) Gen II by Condor Outdoor because it one of the highest selling plate carriers on the market. For good reason, as it is widely used by law enforcement throughout our country. It is designed for modular attachments with MOLLE webbing on all sides as for functionality and operator mobility. The MOPC accepts Caliber Armor AR550 Steel Body Armor Plates in both 10” x 12” and 11” x 14”. If you are purchasing thicker composite/ceramic plates it accommodates 10”x 12” sizes. This plate carrier allows you to either use the full cummerbund or the internal waist strap for a scaled down system when needed. Features Emergency drag handle Removable low profile shoulder pads Adjustable shoulder straps MOLLE webbing for modular attachments Hook and loop webbing Front map pocket with snap, hook and loop closure Breathable 3D Mesh liner Adjustable cummerbund with built-in soft armor pockets Side release buckles Easy access plate pockets Ballistic plates/soft armor not included Imported Accepts Caliber Armor AR550 Steel Plates in 10″ x 12″ and 11″x 14″ or any other ESAPI sizes up to 10.25″ x 13.25 Available in:OD GreenBlackCoyote BrownScorpion OCPBlack Multi-Cam

AR550 Level III+ Steel Body Armor Plate with standard coating to protect the plate from the elements. This package does not have Spall Coating. If you would like this package with Bullet Liner Spall Coating. Ergonomic Multi-Curve design at no extra cost Standard coating to protect against the elements Shooters Cut Rated and tested to: NIJ STD-0101.06 Level III and special threats listed in NIJ STD-0101.07 Draft Rifle 2 Proudly made in the U.S.A Features Emergency drag handle Removable anti-slip shoulder pads, with hook and loop guides Adjustable shoulder straps MOLLE webbing for modular attachments Hook and loop webbing Breathable 3D Mesh liner Quick release buckles Easy access plate pockets Accepts Caliber Armor AR550 Steel Plates in 10″ x 12″ Size: : Adjustable sizing from 32″ – 54″ waist size Available in:OD GreenBlackCoyote BrownScorpion OCP AR550 Multi-Curve Steel Body Armor Plates AR550 Level III+ Steel Body Armor Plate with standard coating to protect the plate from the elements. This package does not have Spall Coating. If you would like this package with Bullet Liner Spall Coating. Ergonomic Multi-Curve design at no extra cost Standard coating to protect against the elements Shooters Cut Rated and tested to: NIJ STD-0101.06 Level III and special threats listed in NIJ STD-0101.07 Draft Rifle 2 Proudly made in the U.S.A We have gone above and beyond to bring you steel body armor of a HIGHER CALIBER. This can be seen with our bend process, our fragmentation coating and our finishing details. This was the material that we started from and have the most experience with. We’ve seen it, done it, we’ve improved it. Steel Body Armor provides great protection that can stop multiple projectile hits. We have been working with different levels of abrasion resistant (AR) ballistic steel for years and have not found a better product than our AR550 Steel Body Armor Plates. This armor is rated at a level III+ as it can defeat special threats like M855 rounds. All of our steel plates come in one ergonomic curve option. We have worked with LE and first responders to design a curve that you can be comfortable wearing. We provide this at no additional cost. What is unique about the way that we bend our steel is important too. We have designed a press that creates a multi curve bend in ONE step. Why is this important? When you do multiple bends to achieve a multi curve, it puts extra strain on the plate which can weaken it. We have replicated the same curves that you have seen in multi curve ceramic armor for years. Our aggressive Shooters Cut body armor plates shaves off weight while still providing enough coverage to protect your vital organs. Use our CaliberX™ Soft Armor Backers for even more protection and comfort. Our standard AR550 plate comes coated to protect the plate from rust and the elements. One concern with Steel Armor is fragmentation containment. Some of that fragmentation is contained in the armor’s plate carrier, but there still is a risk of lethal shrapnel. We HIGHLY recommend our Caliber Anti-Spall add on. We have teamed up with our friends at Bullet Liner® to formulate an anti-spall coating specifically for our armor application. This addition to your steel plate gives you peace of mind when wearing steel armor. Click HERE to see this product with the Advanced Spall and Fragmentation Protection Weights for AR550 Steel Body Armor: 10 x 12 – 7lb 6 oz NIJ STANDARD-0101.06 Tested and verified to meet or exceed ballistic resistance as specified under NIJ Standard- 0101.06 Level III and also tested for special threats listed in the draft  NIJ Standard- 0101.07 Rifle 2. MANUFACTURING TOLERANCES: Thickness dimensions are +-1/8 in. Width and length dimensions are +0.00 to 0.25 in. All weights are +- 5%. Sentry Plate Carrier Caliber Armor offers the Sentry Plate Carrier by Condor Outdoor because it one of the highest selling plate carriers on the market. For good reason, as it is widely used by law enforcement throughout our country. It is designed for modular attachments with quick release and cinch buckles. This carrier accepts Caliber Armor AR550 Steel Body Armor Plates in  10” x 12”. This package is is perfect for rapid response situations or to add to your workout routine. Features Emergency drag handle Removable anti-slip shoulder pads, with hook and loop guides Adjustable shoulder straps MOLLE webbing for modular attachments Hook and loop webbing Breathable 3D Mesh liner Quick release buckles Easy access plate pockets Accepts Caliber Armor AR550 Steel Plates in 10″ x 12″ Size: : Adjustable sizing from 32″ – 54″ waist size Available in:OD GreenBlackCoyote BrownScorpion OCP

Features: 500D Cordura material Mesh lined for comfort and ventilation Removable, padded mesh shoulder pads Hook-and-loop webbing on front and back Drag handle Adjustable shoulder straps and waist Quick release buckles on shoulders and waist Designed for 10"X12" plates 100% Made in the USA Predator Armor Minuteman Plate Carrier The Minuteman Plate Carrier is the perfect minimalist plate carrier. Designed to carry 10"X12" plates. There are six rows of MOLLE/PALS style webbing with built in matching loop material on the top three rows for the option of attaching patches or other items. Made one size to fit most, the shoulder and waist straps are adjustable, providing a snug fit. It also has removable mesh shoulder pads providing comfort while wearing. The inside of the carrier is mesh providing more breathability and comfort.  While being a minimalist carrier there is no sacrifice on quality and performance. Constructed from mil-spec material it is made to withstand whatever use you throw its way.   Features: 500D Cordura material Mesh lined for comfort and ventilation Removable, padded mesh shoulder pads Hook-and-loop webbing on front and back Drag handle Adjustable shoulder straps and waist Quick release buckles on shoulders and waist Designed for 10"X12" plates 100% Made in the USA

In addition to stopping the 7.62x51 M80 Ball at 2780 FPS, our PE plate has also been Special Threat tested against the following rounds: 5.56x45 M193 at 3150 FPS 7.62x39 AK-47 at 2380 FPS Highlights Peace of mind: Tested to NIJ Standard 0101.06 Level III and is multi-hit capable  Confidence: stops high-velocity military 5.56 and .30 caliber ammunition Safety: At 3.5 pounds, our PE plate is neutrally buoyant Specifications Tested to Level III threats 10”x12” plate weighs only 3.5 lbs Stand-Alone and Multi-Hit capable 1” Thick Profile Ergonomic Multiple Axis Curvature Durable polyurea coating seals out water and the elements Made in our Phoenix, Arizona, facility AR500 Armor Level III Lightweight UHMWPE Body Armor 10" x 12" There is a saying in the backpacking community, “take care of the ounces, and the pounds will take care of themselves.” When weight and mobility are everything in your body armor, the AR500 Armor® Level III ultra-high molecular weight polyethylene plate is the clear choice. Ultra-light Level III protection Our UHMWPE (aka PE) plate weighs a mere 3.5 pounds in our 10”x12” standard shooters cut. This stand-alone plate is tested to NIJ 0101.06 Level III threats and is multi-hit capable. It is manufactured in Phoenix, Arizona, and carries a 5-year shelf life. Our new PE lightweight armor plate is a great choice for those whose primary concern is weight.  In addition to stopping the 7.62x51 M80 Ball at 2780 FPS, our PE plate has also been Special Threat tested against the following rounds: 5.56x45 M193 at 3150 FPS 7.62x39 AK-47 at 2380 FPS Highlights Peace of mind: Tested to NIJ Standard 0101.06 Level III and is multi-hit capable  Confidence: stops high-velocity military 5.56 and .30 caliber ammunition Safety: At 3.5 pounds, our PE plate is neutrally buoyant Specifications Tested to Level III threats 10”x12” plate weighs only 3.5 lbs Stand-Alone and Multi-Hit capable 1” Thick Profile Ergonomic Multiple Axis Curvature Durable polyurea coating seals out water and the elements Made in our Phoenix, Arizona, facility Note: Due to its size and profile, this plate currently fits in our Testudo Gen 2.0 and AR Independence carriers only.

SPECIFICATIONS Material: Ballistic steel of 650 hardness on the Brinell scale, with FragLock™ Coating Protection: 5.56x45 M193, 5.56x45 M855/SS109 at 3,100 FPS (+/- 30FPS), 7.62x51 M80 Ball (ie .308) at 3,000 FPS (+/- 30FPS), and DEA Certified FPS and 5.56mm M855/SS109 (Green Tip) at a velocity of 2,780 FPS Capability: Edge-to-edge multi-hit protection  Dimensions: 10"x12" Base Coat Weight: 8 lbs Thickness: 0.31" Build-Up Coat Weight: 9.5 lbs Thickness: 0.56" 11”x14” Base Coat Weight: 10 lbs Thickness: 0.31" Build-Up Coat Weight: 11.5 lbs Thickness: 0.56" Shelf life: 20 years Compatibility: Testudo, Veritas, Valkyrie, Independence & Invictus Carriers Manufactured: United States AR500 Armor Level III+ Body Armor With Build Up Coat The Level III+ Steel Plate (specifications below) is able to stop threats such as 7.62x39/7.62x51/5.56 M193s, 5.56 M855 penetrators, and .223/.308 WIN rounds. And unlike ceramic or polyethylene, Steel is able to take several hits from these rounds without fail. This multi-hit special threat resistance is the distinguishing quality of the Level III Plus. The plate features our patented Advanced Shooter Cut, which improves comfort and shooting ergonomics by affording you extra room for your rifle cut. It is available in both right and left-handed versions and is compatible with all standard plate carriers that accept SAPI or traditional Shooters Cut body armor (given you have an appropriate carrier size).  The included FragLock™ Coat is a feature special to our AR500 Armor plates, which we apply for two reasons: First, it helps reduce the dangers of spalling (when broken pieces of steel come off the plate) and fragmentation (when a bullet’s remains bounce off the plate), protecting you from the aftermath of a bullet’s impact once it has been stopped. Second, the coat gives our plates a maintenance-free shelf life of twenty years, which makes this steel plate last much longer than polyethylene or ceramic alternatives. The Base Coat, which all our plates come with by default, is lighter and thinner with less protection, while the Build-Up Coat can be added for greater protection but also slightly more weight. SPECIFICATIONS Material: Ballistic steel of 650 hardness on the Brinell scale, with FragLock™ Coating Protection: 5.56x45 M193, 5.56x45 M855/SS109 at 3,100 FPS (+/- 30FPS), 7.62x51 M80 Ball (ie .308) at 3,000 FPS (+/- 30FPS), and DEA Certified FPS and 5.56mm M855/SS109 (Green Tip) at a velocity of 2,780 FPS Capability: Edge-to-edge multi-hit protection  Dimensions: 10"x12" Base Coat Weight: 8 lbs Thickness: 0.31" Build-Up Coat Weight: 9.5 lbs Thickness: 0.56" 11”x14” Base Coat Weight: 10 lbs Thickness: 0.31" Build-Up Coat Weight: 11.5 lbs Thickness: 0.56" Shelf life: 20 years Compatibility: Testudo, Veritas, Valkyrie, Independence & Invictus Carriers Manufactured: United States

Our Rimelig option is made of p-Aramid Fibers and is available at both Level II and Level IIIA protection levels, which both provide multi-hit protection. The Rimelig is the most budget option of the three, making it a solid entry-level soft armor option, while still staying true to the goal of soft armor: Reliable lightweight protection, at just 0.45” thick and weighing 1.24 pounds. The next level up is the Slim, which is made of two separate Aramid laminates joined together for greater strength. The symmetrical design of our Slim armor gives it a bidirectional capability, meaning it's perfect for use in a backpack, where you might use it on your back, or in front of you as a shield (slim armor panels will still have a "strike face" label, though it will be equally effective from either side, making it perfect for use in armored backpacks or bags). It provides Level IIIA protection and is only 0.36” and 1.25 pounds in our 10x12 ASC model. Finally, for our most advanced option, the Hybrid is constructed from industry-leading materials from Honeywell Spectra Shield®, Honeywell Gold Shield®, and other ballistic fabric from respected manufacturers. The exceptional quality of these materials makes for an especially capable panel. The result is an ultra-thin and ultra-light piece of soft armor at 0.25” thick, 1.04 pounds. SPECIFICATIONS Material Rimelig: p-Aramid Fibers Slim: two separate Aramid Hybrid: Honeywell Spectra Shield®, Honeywell Gold Shield®, and other ballistic fabric from respected manufacturers Protection Level II (Rimelig): 124-grain 9mm FMJ RN bullets with a velocity of 1305 ft/s (± 30 ft/s) and with 158-grain .357 Magnum Jacketed Soft Point (JSP) bullets with a velocity of 1430 ft/s (± 30 ft/s) Level IIIA (Rimelig, Slim & Hybrid): 125-grain .357 SIG FMJ flat-nose bullets with a velocity of 1470 ft/s (± 30 ft/s) and with 240-grain .44 Magnum Semi-Jacketed Hollow Point (SJHP) bullets with a velocity of 1430 ft/s (± 30 ft/s) Capability: Multi-hit protection  Dimensions (chart below) Shelf life: 5 years Manufactured: United States AR500 Armor Soft Body Armor For lightweight protection that’s easy to carry, AR500 Armor’s soft armor (specifications below) options give you the most value for the least sacrifice in affordability and stopping power.  Multiple soft armor types are available to choose from, each of which uses a different soft armor material with different weights and protection levels. However, there are similarities across each option: Every panel is either rated at Level II and Level IIIA (two handgun threat levels from the NIJ recommendations). Every soft armor panel is cut, sewn, and assembled in-house. And, like ceramic and polyethylene hard armor, these panels all have a 5-year shelf life. Our Rimelig option is made of p-Aramid Fibers and is available at both Level II and Level IIIA protection levels, which both provide multi-hit protection. The Rimelig is the most budget option of the three, making it a solid entry-level soft armor option, while still staying true to the goal of soft armor: Reliable lightweight protection, at just 0.45” thick and weighing 1.24 pounds. The next level up is the Slim, which is made of two separate Aramid laminates joined together for greater strength. The symmetrical design of our Slim armor gives it a bidirectional capability, meaning it's perfect for use in a backpack, where you might use it on your back, or in front of you as a shield (slim armor panels will still have a "strike face" label, though it will be equally effective from either side, making it perfect for use in armored backpacks or bags). It provides Level IIIA protection and is only 0.36” and 1.25 pounds in our 10x12 ASC model. Finally, for our most advanced option, the Hybrid is constructed from industry-leading materials from Honeywell Spectra Shield®, Honeywell Gold Shield®, and other ballistic fabric from respected manufacturers. The exceptional quality of these materials makes for an especially capable panel. The result is an ultra-thin and ultra-light piece of soft armor at 0.25” thick, 1.04 pounds. SPECIFICATIONS Material Rimelig: p-Aramid Fibers Slim: two separate Aramid Hybrid: Honeywell Spectra Shield®, Honeywell Gold Shield®, and other ballistic fabric from respected manufacturers Protection Level II (Rimelig): 124-grain 9mm FMJ RN bullets with a velocity of 1305 ft/s (± 30 ft/s) and with 158-grain .357 Magnum Jacketed Soft Point (JSP) bullets with a velocity of 1430 ft/s (± 30 ft/s) Level IIIA (Rimelig, Slim & Hybrid): 125-grain .357 SIG FMJ flat-nose bullets with a velocity of 1470 ft/s (± 30 ft/s) and with 240-grain .44 Magnum Semi-Jacketed Hollow Point (SJHP) bullets with a velocity of 1430 ft/s (± 30 ft/s) Capability: Multi-hit protection  Dimensions (chart below) Shelf life: 5 years Manufactured: United States Product Comparisons Body Armor Thickness (all) 10"x12" 11"x14" 11"x15" (backpack) II Rimelig 0.45" 1.24 lbs n/a n/a IIIA Rimelig 0.55" 1.43 lbs 1.75 lbs 1.95 lbs IIIA Slim 0.36" 1.25 lbs 1.54 lbs 1.76 lbs IIIA Hybrid 0.25" 1.04 lbs 1.30 lbs 1.47 lbs  

SPECIFICATIONS Material: Ballistic steel of 650 hardness on the Brinell scale, with FragLock™ Coating Protection: 5.56x45 M193, 5.56x45 M855/SS109 at 3,000 FPS (+/- 30FPS) and 7.62x39(ie AK-47), 7.62x51 M80 NATO Ball (ie .308) at 2,850 FPS. Not rated for AP rounds. Capability: Edge-to-edge multi-hit protection  Size & Weight:  10”x12” Base Coat: 7 lbs Build-Up Coat: 7.5 lbs Shelf life: 20 years Compatibility: Testudo, Veritas, Valkyrie, Independence & Invictus Carriers Manufactured: United States AR500 Armor Level III+ Lightweight ASC Body Armor Our Level III+ Lightweight ASC (see specifications below) is tested to defeat .223/.308 WIN rounds, 5.56 M855 penetrators, and 7.62x39/7.62x51/5.56 M193s all at bullet speeds of up to 3,000 feet per second. Also, thanks to the virtues of steel armor, this plate is capable of stopping several shots without shattering or buckling like ceramic and polyethylene alternatives. The plate is shaped according to the designs of our Advanced Shooter Cut (ASC), with the taper to the top of the plate asymmetrical. This makes using your strong arm easier because of the space given by the cut, making actions like shouldering your rifle easier. This cut comes in both right and left-handed configurations, and any appropriately sized plate will accept it just as well as it would a SAPI or traditional Shooters Cut. Finally, the FragLock™ sealing from AR500 Armor, which can come either as a Base Coat or as a Build-Up Coat, gives two benefits: First, it acts as a protection from bullet or armor fragments that may come off after a