$500 - $1000

Shellback Tactical Level IIIA Ballistic High Cut SF ACH Helmet The Shellback Tactical Level IIIA Ballistic High Cut SF ACH Helmet is our top of the line elite ballistic helmet designed for special operation missions.  This helmet features side rails, 3 hole nvg shroud, loop panels, bungee cords and ratcheting retention system. The low profile high cut design provides easy access to radio headsets, reduced weight and easy target acquisition without interference. This helmet provides level IIIA ballistic and frag protection. Be ready for the fight and order your Shellback Tactical Level IIIA Ballistic High Cut SF ACH Helmet today!  Specifications ACH - Advance Combat Helmet  Meets NIJ 0106.01 Standard   Level IIIA ballistic protection against handgun rounds  Fragmentation protection according to Milstd 662f standards High cut design is lightweight and increases mobility  Constructed with Kevlar fibers and thermoset resin Retention harness with ratcheting system for perfect fit  Side rails fit picatinny and other common adapters which is perfect for tactical lights and cameras  3 hole shroud is compatible with most modern NVG mounts such as Wilcox and Norotos Loop field allows for the secure, quick and easy attachment of helmet accessories  D30 Trust 7 helmet pad system provides extra comfort 5 Year Ballistic Warranty   Sizing Circumference is measured around head, similar to hat sizing. All sizes are measured in inches. If a measurement falls on a dividing line between sizes, select the larger of the two sizes. Medium Circumference - 21.9" to 22.7" Hat Size - 6 7/8 - 7 1/8 Weight - 3.1 lbs Large  Circumference - 22.7" to 24" Hat Size - 7 1/4 - 7 3/8 Weight - 3.2 lbs  XLarge Circumference - 24" to 26" Hat Size - 7 1/2 to 7 3/4 Weight - 3.4 lbs  Rounds Defeated 357 SIG FMJ  9MM .38 .40 S&W .44 MAG LEGAL THIS IS A ITAR CONTROLLED ITEM AND WILL ONLY BE SHIPPED TO US ADDRESSES.  DUE TO THE NATURE OF THE ITEM - ALL SALES ARE FINAL.     

Advanced plate carrier that is feature packed 500 Denier  Front Top Zippered Admin Pouch Front Lower Velcro kangaroo pouch PALS web attachment points covering the front, back and shoulders of the vest Mil spec laser cut PALS Webbing on the shoulders Cummerbund is designed to hold a 5"x15" IIIA soft armor inside each side. Cummerbund has a proprietary retained shock cord system to allow stretch while being held in place to stop sagging. Cummerbund is removable and the carrier is equipped with removable quick release buckles Genuine US Mil Spec Webbing Velcro on the back Drag Handle keeps it in place Heavy Duty bar tacking at key stress points Communication or hydration hose guides  Padded Front and back interior of carrier with airflow channels sewn in Front and back areas of Velcro for identifiers Bottom Loading Plate Pockets accepts 10x12, SAPI and Similar Armor All pieces Made in USA, assembled in Mexico *Note* This plate carrier by itself will only hold 5x15 Soft Armor Panels, this package will come with a molle system to attach on your 6x6 or 6x8 side plates.  Leonidas Plate Carrier System with Spartan Armor Systems™ Omega™ AR500 Body Armor The Leonidas plate carrier is an advanced plate carrier system is fit for a Spartan King, hence the name "Leonidas". This versatile plate carrier hosts a wide variety of proven features including a removable cummerbund. When you are looking for the toughest plate carrier available to take into battle this is it. Take a look at all the features below. Advanced plate carrier that is feature packed 500 Denier  Front Top Zippered Admin Pouch Front Lower Velcro kangaroo pouch PALS web attachment points covering the front, back and shoulders of the vest Mil spec laser cut PALS Webbing on the shoulders Cummerbund is designed to hold a 5"x15" IIIA soft armor inside each side. Cummerbund has a proprietary retained shock cord system to allow stretch while being held in place to stop sagging. Cummerbund is removable and the carrier is equipped with removable quick release buckles Genuine US Mil Spec Webbing Velcro on the back Drag Handle keeps it in place Heavy Duty bar tacking at key stress points Communication or hydration hose guides  Padded Front and back interior of carrier with airflow channels sewn in Front and back areas of Velcro for identifiers Bottom Loading Plate Pockets accepts 10x12, SAPI and Similar Armor All pieces Made in USA, assembled in Mexico *Note* This plate carrier by itself will only hold 5x15 Soft Armor Panels, this package will come with a molle system to attach on your 6x6 or 6x8 side plates.  Spartan™ Omega™ AR500 Body Armor - High Quality Ballistic Threat Protection With all of our Spartan™ Omega™ AR500 Body Armor products, we only use ballistic LAB CERTIFIED AR500 steel! All purchases of our Spartan Armor products have current lab certificates available on request. Remember, not all body armor is created equal! Read our "FAQ" to find out more about Spartan™ Omega™ AR500 Body Armor and the steel we use to construct our body armor! You have the choice of getting our Spartan™ Omega™ AR500 Body Armor formed on a continual radius die. Or with our Advanced Triple Curve ™.  Instead of bending our formed plates in 2 different locations as we used to, we have machined custom tooling to give these plates a nice curvature to best conform to the side of your torso. Spartan Armor Systems™ is proud to be the FIRST in the industry to commercially offer triple-curved Spartan™ Omega™ AR500 Body Armor. Spartan Armor Systems’ ATC™ body armor allows the operator to shoulder their weapon with the most freedom and limited discomfort. The ATC™ armor better “hugs” the operator’s body, resulting in a significant increase in comfort. Our CNC equipment capabilities have allowed us to create dies which form our body armor without any “crease” bends. Crease bends, “work hardens” the plate and causes a significant amount of stress to the portion of the plate under load. We HIGHLY suggest when doing research to ask if they crease bend their body armor. This process results in increased potential for plate fatigue and failure, which is why Spartan Armor Systems™ has gone the extra mile to create this die process. These plates come as a pair.  Full Coat or Base Coat Options:  We are excited to announce our potentially “life saving” breakthrough!  The strike face for our plates is mark embedded with our Spartan logo! Both sides of these plates are coated, however, the back side only has a “courtesy coat” to protect against wear and rust. The front of the plate is lined with 1/4-3/8 of our proprietary coating, Encapsaloc ™.  The result is a plate approximately 1/2-5/8” total thickness.  See our FAQ for more information about our Encapsaloc ™ process. By purchasing, you will receive (2) Formed Spartan™ Omega™ AR500 Body Armor 10″x12” chest plates.  Due to popular demand, we have added a “base coat” only option for our AR500 Omega™ armor products. The base coat option has an extremely thin layer of our fragmentation mitigation coating to aesthetically enhance the plates, and to provide corrosion resistance. This coating has minimal, if any, fragmentation mitigation capabilities.

Kit Components  Shellback Tactical Banshee Elite Plate Carrier x 1 Shellback Tactical Model LON-III-P Plates x 2 Shellback Banshee Elite 2.0 Plate Carrier Features  Constructed of durable 500 denier nylon Plate pockets load from the bottom and hold 10 x 12 plates  Integrated zipper admin pouch located on chest  Extreme versatility with PALS webbing covering the front, back and shoulders of the vest 3D Mesh padding for comfort and allows air flow to keep you cool  Hypalon shoulder straps for radio wires and hydration tubes  Rear drag handle lays flat and secures with hook and loop Heavy duty bar tacking at key stress points for durability Quick release buckles on shoulders for quick on and off access  Removable cummerbund with interior and exterior PALS for side plate pocket attachment Cummerbund includes 6 integrated pockets with bungee retention for magazines or radios Cummerbund accepts 13.75" x 5.5" soft armor inserts  Carrier is fully adjustable at cummerbund and shoulder straps to fit all body types Built in rear hydration pocket accepts most common bladders Integrated nylon vertical strips to accommodate QASM buckles Two areas of loop on front and rear for id placards GSA and TAA compliant Lifetime Warranty  Shellback Prevail Series Model LON-III-P Level III Armor Plates  NIJ threat level III NIJ 0101.06 Certified  Listed on NIJ Compliant Products List 10"W x 12"L x 1.1"W  Weight 3.5 LBS  Single Curve  ESAPI/SAPI cut  UHWMP construction - ultra high weight molecular polyethylene  Multihit rated  600 Denier water resistant cover Positive Buoyancy USA Made 10 Year Ballistic Warranty  Stopping power .357 SIG FMJ  9MM .38 .40 S&W .44 .45 .223 BALL  5.56X45 (XM 193) 7.62 X 39 BALL  7.62 x 51 M80 Nato Shellback Tactical Banshee Elite 2.0 Lightweight Armor System with Level III LON-III-P Plates The Shellback Tactical Banshee Elite 2.0 Lightweight Armor System is your ultimate lightweight armor solution with a total combined weight of 9.6 LBS.  This kit combines our most advanced Banshee Elite 2.0 Plate Carrier with level III model LON-III-P hard armor plates. The Shellback Tactical Banshee Elite 2.0 Lightweight Armor System is the perfect kit for SWAT, SRT and tactical teams where mobility and function is paramount.  Kit Components  Shellback Tactical Banshee Elite Plate Carrier x 1 Shellback Tactical Model LON-III-P Plates x 2 Shellback Banshee Elite 2.0 Plate Carrier Features  Constructed of durable 500 denier nylon Plate pockets load from the bottom and hold 10 x 12 plates  Integrated zipper admin pouch located on chest  Extreme versatility with PALS webbing covering the front, back and shoulders of the vest 3D Mesh padding for comfort and allows air flow to keep you cool  Hypalon shoulder straps for radio wires and hydration tubes  Rear drag handle lays flat and secures with hook and loop Heavy duty bar tacking at key stress points for durability Quick release buckles on shoulders for quick on and off access  Removable cummerbund with interior and exterior PALS for side plate pocket attachment Cummerbund includes 6 integrated pockets with bungee retention for magazines or radios Cummerbund accepts 13.75" x 5.5" soft armor inserts  Carrier is fully adjustable at cummerbund and shoulder straps to fit all body types Built in rear hydration pocket accepts most common bladders Integrated nylon vertical strips to accommodate QASM buckles Two areas of loop on front and rear for id placards GSA and TAA compliant Lifetime Warranty  Shellback Prevail Series Model LON-III-P Level III Armor Plates  NIJ threat level III NIJ 0101.06 Certified  Listed on NIJ Compliant Products List 10"W x 12"L x 1.1"W  Weight 3.5 LBS  Single Curve  ESAPI/SAPI cut  UHWMP construction - ultra high weight molecular polyethylene  Multihit rated  600 Denier water resistant cover Positive Buoyancy USA Made 10 Year Ballistic Warranty  Stopping power .357 SIG FMJ  9MM .38 .40 S&W .44 .45 .223 BALL  5.56X45 (XM 193) 7.62 X 39 BALL  7.62 x 51 M80 Nato LEGAL THIS IS A ITAR CONTROLLED ITEM AND WILL ONLY BE SHIPPED TO US ADDRESSES.  DUE TO THE NATURE OF THE ITEM - ALL SALES ARE FINAL.     

Shellback Tactical SF Lightweight Armor System with Level III+ H3101 Plates The Shellback Tactical SF Lightweight Armor System is a super lightweight sized armor solution that provides level III+ threat protection. This kit features our SF plate carrier with two level III+ model H3101 plates. The Shellback Tactical SF Lightweight Armor System is the perfect kit for SWAT, SRT and military operations where mobility and function is paramount.  Kit Components  Shellback Tactical SF Plate Carrier x 1 Shellback Tactical Model H3101 Plates x 2 SF Plate Carrier Features  Constructed of durable 500 Denier Nylon  Front and rear plate pockets load from the bottom 3D Spacer mesh padding on front, rear and shoulder pads for comfort  Cummerbund has two integrated pockets for 6x6 or 6x8 Plates Cummerbund has integrated radio pouch for Police or MBITR radios with secure snap Cummerbund integrated padded comfort flap Extreme versatility with several PALS web attachment points covering the front, back and shoulders of the vest Front and Back areas of loop for placard identifiers Integrated kangaroo pouch accepts three .223/5.56 magazines Rear drag handle Heavy duty bar tacking at key stress points Fully adjustable shoulder straps to fit most sizes   Fully adjustable cummerbund to fit most sizes  Lifetime Warranty  GSA and TAA compliant SF Plate Carrier Sizing Chart  The below chart refers carrier size and the plates that fit each size. Small - 8.75" Wide x 11.75" Tall Medium - 9.5" Wide x 12.5" Tall Large - 10.25" Wide x 13.25" Tall XLarge - 11" Wide x 14" Tall Level III+ Model H3101 Plate Features  NIJ threat level III+ NIJ 0101.06 Certified Listed on NIJ Compliant Products List Special threat rated Single curve SAPI/ESAPI Cut Stand alone protection Single plate Ceramic and Polyethylene construction 600 Denier water resistant cover 10 year ballistic warranty Multihit rated 7.62 X 51 Nato (M80) - 6 Rounds 5.56X45 (XM 193) - 6 Rounds 5.56 X 45 SS109 (M855) - 6 Rounds 7.62 X 39 AK47 API BZ - 3 Rounds 7.62 X 39 AK47 MSC - 6 Rounds 7.62 x 54R LPS - 3 Rounds .300 Win Mag - 3 Rounds Sized Small - 8.75" Wide x 11.75" Tall Weight - 4.4lbs Medium - 10" Wide x 12.5" Tall Weight - 4.7lbs Large - 10.25" Wide x 13.25" Tall Weight - 5.5lbs XLarge - 11" Wide x 14" Tall Weight - 6.5lbs Rounds Defeated  357 SIG FMJ  9MM .38 .40 S&W .44 .45 .223 BALL  7.62 X 39 BALL  7.62 X 51 Nato (M80) 5.56X45 (XM 193) 5.56 X 45 SS109 (M855) 7.62 X 39 AK47 API BZ  7.62 X 39 AK47 MSC 7.62 x 54R LPS  .300 Win Mag 

Sizing for Caliber X™ Covert Body Armor Vest: Measure your waist with a soft measuring tape from your navel all the way around. You will want to make sure that you order the size that is equal to or more than that measurement. When in doubt go a size up to avoid any gap. Small: Maximum 33″ Medium-Large: Maximum 41″ Large-2 XL: Maximum 51″ 3-4 XL: Maximum 60″ Smaller and larger sizes can be custom made. Please inquire for more details. All of our CaliberX™ soft armor thinness is .19 in. and weigh just over 1 lb. per sqft. Small: 3.33 lb Medium-Large: 4 lb Large-2XL: 5.67 lb 3XL-4XL: 6.89 lb Caliber Armor CaliberX Covert Body Armor Vest At Caliber Armor, we are always striving to offer our customers the best possible protection combined with maximum comfort, low weight and competitive pricing. Introducing our CaliberX™ Covert Body Armor Vest. This fully concealable body armor setup starts with high tech Kevlar XP para-aramid material and is finished with a minimalist carrier that produces a light and flexible concealable body armor platform that can be worn comfortably through long shifts. All CaliberX™ body armor is NIJ 0101.06 Level IIIA and 0101.07 RF2 rated to stop multiple hits from most pistol and shotgun rounds including .44 Magnum, .357 Sig, and .9 mm. This full coverage soft armor option can be worn flush together or overlapped for maximum side protection. It is designed to be worn under street clothes or uniforms for an extended period of time. This is the choice for departments looking for an extremely concealed and comfortable solution. Our simplistic functional carrier is thin, breathable and has multiple adjustment options. It allows the armor to lay smooth under clothing to avoid being obvious that you are wearing body armor. We have fully maximized the material’s potential and made it more comfortable and lighter for the wearer. Our CaliberX™ ballistic vests offer better flexibility and comfort, greatly improving response time in a critical moment which could mean the difference between life and death. Designed to be worn under uniform or street clothes for undercover operations. This maximum conceal ability allows you to pass without others being fully aware that you are wearing ballistic protection. All of our armor products can be worn by men or women. Due to the thinness and flexibility it is easily concealable even on those with smaller frames. We have a size for you. Beware of any armor that does not list or boast about where it’s made (it’s probably Chinese). If they don’t tell you how thick or heavy, it is (it’s heavy and bulky)! We strive for transparency at Caliber Armor. If you ever have any questions about our armor, we are a quick email or call away. Any product that we put our name on is proudly designed and made in the U.S.A Sizing for Caliber X™ Covert Body Armor Vest: Measure your waist with a soft measuring tape from your navel all the way around. You will want to make sure that you order the size that is equal to or more than that measurement. When in doubt go a size up to avoid any gap. Small: Maximum 33″ Medium-Large: Maximum 41″ Large-2 XL: Maximum 51″ 3-4 XL: Maximum 60″ Smaller and larger sizes can be custom made. Please inquire for more details. All of our CaliberX™ soft armor thinness is .19 in. and weigh just over 1 lb. per sqft. Small: 3.33 lb Medium-Large: 4 lb Large-2XL: 5.67 lb 3XL-4XL: 6.89 lb

Kit Components  Shellback Tactical Rampage 2.0 Plate Carrier x 1 Shellback Tactical Model LON-III-P Plates x 2 Rampage 2.0 Plate Carrier Features  Constructed of durable 500 Denier Nylon  Front and rear plate pockets hold 10" x 12" shooter or SAPI cut ballistic plates  Laser cut Molle on front, rear and cummerbund to accessorize with pouches  Laser cut Molle loop panels on front and rear for ID placards  3D Spacer mesh padding on front, rear and shoulder pads for comfort  Removable front Molle placard  Cummerbund includes six integrated pockets with bungee retention for magazines or radios Cummerbund accepts 13.75" x 5.5" soft armor inserts  Rear drag handle Heavy duty bar tacking at key stress points Fully adjustable shoulder straps to fit most sizes   Fully adjustable cummerbund to fit most sizes  Lifetime Warranty  Imported  Shellback Prevail Series Model LON-III-P Level III Armor Plates  NIJ threat level III NIJ 0101.06 Certified  Listed on NIJ Compliant Products List 10"W x 12"L x 1.1"W  Weight 3.5 LBS  Single Curve  ESAPI/SAPI cut  UHWMP construction - ultra high weight molecular polyethylene  Multihit rated  600 Denier water resistant cover Positive Buoyancy USA Made 10 Year Ballistic Warranty  Stopping power .357 SIG FMJ  9MM .38 .40 S&W .44 .45 .223 BALL  5.56X45 (XM 193) 7.62 X 39 BALL  7.62 x 51 M80 Nato Shellback Tactical Rampage 2.0 Lightweight Armor System with Level III LON-III-P Plates The Shellback Tactical Rampage 2.0 Lightweight Armor System is a super lightweight armor solution with a total combined weight of 9.6 LBS.  This kit combines our Rampage 2.0 plate carrier with level III model LON-III-P hard armor plates. The Shellback Tactical Rampage 2.0 Lightweight Armor System is the perfect kit for SWAT, SRT and tactical teams where mobility and function is paramount.  Kit Components  Shellback Tactical Rampage 2.0 Plate Carrier x 1 Shellback Tactical Model LON-III-P Plates x 2 Rampage 2.0 Plate Carrier Features  Constructed of durable 500 Denier Nylon  Front and rear plate pockets hold 10" x 12" shooter or SAPI cut ballistic plates  Laser cut Molle on front, rear and cummerbund to accessorize with pouches  Laser cut Molle loop panels on front and rear for ID placards  3D Spacer mesh padding on front, rear and shoulder pads for comfort  Removable front Molle placard  Cummerbund includes six integrated pockets with bungee retention for magazines or radios Cummerbund accepts 13.75" x 5.5" soft armor inserts  Rear drag handle Heavy duty bar tacking at key stress points Fully adjustable shoulder straps to fit most sizes   Fully adjustable cummerbund to fit most sizes  Lifetime Warranty  Imported  Shellback Prevail Series Model LON-III-P Level III Armor Plates  NIJ threat level III NIJ 0101.06 Certified  Listed on NIJ Compliant Products List 10"W x 12"L x 1.1"W  Weight 3.5 LBS  Single Curve  ESAPI/SAPI cut  UHWMP construction - ultra high weight molecular polyethylene  Multihit rated  600 Denier water resistant cover Positive Buoyancy USA Made 10 Year Ballistic Warranty  Stopping power .357 SIG FMJ  9MM .38 .40 S&W .44 .45 .223 BALL  5.56X45 (XM 193) 7.62 X 39 BALL  7.62 x 51 M80 Nato LEGAL THIS IS A ITAR CONTROLLED ITEM AND WILL ONLY BE SHIPPED TO US ADDRESSES.  DUE TO THE NATURE OF THE ITEM - ALL SALES ARE FINAL. 

Kit Components  Shellback Tactical Banshee Rifle Plate Carrier® x 1 Shellback Tactical Model LON-III-P Plates x 2 Shellback Banshee Rifle Plate Carrier® Features  Constructed of durable 500 Denier Nylon   Removable cummerbund with interior and exterior PALS for side plate pocket attachment Cummerbund accepts 13.75" x 5.5" soft armor inserts  Quick release secondary securing system Extreme versatility with PALS webbing attachment points covering the front, back and shoulders of the vest Fully adjustable and padded front, back and shoulder areas. Two areas of loop on front and rear for id placards Front pocket accepts kangaroo inserts  Heavy duty bar tacking at key stress points Wire, antenna or hydration hose guides Low profile design for mobility  Rear drag handle  Lifetime warranty  Shellback Prevail Series Model LON-III-P Level III Armor Plates  NIJ threat level III NIJ 0101.06 Certified  Listed on NIJ Compliant Products List 10"W x 12"L x 1.1"W  Weight 3.5 LBS  Single Curve  ESAPI/SAPI cut  UHWMP construction - ultra high weight molecular polyethylene  Multihit rated  600 Denier water resistant cover Positive Buoyancy USA Made 10 Year Ballistic Warranty  Stopping power .357 SIG FMJ  9MM .38 .40 S&W .44 .45 .223 BALL  5.56X45 (XM 193) 7.62 X 39 BALL  7.62 x 51 M80 Nato Shellback Tactical Banshee Rifle Lightweight Armor System with Level III LON-III-P Plates The Shellback Tactical Banshee Rifle Lightweight Armor System is your complete lightweight armor solution.  This kit combines our most popular Banshee Rifle Plate Carrier with two Level III Model LON-III-P hard armor plates. The total weight for the entire kit (carrier plus two plates) is only 9.2 LBS.  This lightweight armor system is the perfect kit for SWAT, SRT and tactical teams where mobility is essential.  Kit Components  Shellback Tactical Banshee Rifle Plate Carrier® x 1 Shellback Tactical Model LON-III-P Plates x 2 Shellback Banshee Rifle Plate Carrier® Features  Constructed of durable 500 Denier Nylon   Removable cummerbund with interior and exterior PALS for side plate pocket attachment Cummerbund accepts 13.75" x 5.5" soft armor inserts  Quick release secondary securing system Extreme versatility with PALS webbing attachment points covering the front, back and shoulders of the vest Fully adjustable and padded front, back and shoulder areas. Two areas of loop on front and rear for id placards Front pocket accepts kangaroo inserts  Heavy duty bar tacking at key stress points Wire, antenna or hydration hose guides Low profile design for mobility  Rear drag handle  Lifetime warranty  Shellback Prevail Series Model LON-III-P Level III Armor Plates  NIJ threat level III NIJ 0101.06 Certified  Listed on NIJ Compliant Products List 10"W x 12"L x 1.1"W  Weight 3.5 LBS  Single Curve  ESAPI/SAPI cut  UHWMP construction - ultra high weight molecular polyethylene  Multihit rated  600 Denier water resistant cover Positive Buoyancy USA Made 10 Year Ballistic Warranty  Stopping power .357 SIG FMJ  9MM .38 .40 S&W .44 .45 .223 BALL  5.56X45 (XM 193) 7.62 X 39 BALL  7.62 x 51 M80 Nato LEGAL THIS IS A ITAR CONTROLLED ITEM AND WILL ONLY BE SHIPPED TO US ADDRESSES.  DUE TO THE NATURE OF THE ITEM - ALL SALES ARE FINAL.